Logo

Search:

Type: Posts; User: racerone

Page 1 of 4 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    2
    Views
    7

    Re: 1995 20 hp driveshaft seals

    Sounds like a good inspection of lower unit is needed.----If driveshaft is deemed to be good then a new shaft won't help !
  2. Re: 1976 merc 20 hp motor turns easily till I put in the spark plugs

    Where you able to start it OK last year ?-----
  3. Replies
    4
    Views
    25

    Re: Coil Locating Ring 317001

    A couple of clicks on this site and it will be on your door step.-----Just a little under $100.----Box at the top of this page.----Enter the part #-------I have that tool.----If I was desperate for...
  4. Re: Just water draining from lower unit, no oil

    Well I think you should be taking it apart now for inspection.-----Would give you all winter to repair / look for budget parts !
  5. Re: Just water draining from lower unit, no oil

    This sounds serious.----Put some oil ( even peanut oil ) in there while you decide what to do.------Corrosion of bearings is an issue.-----I doubt you drained an " impeller casing "--------I say...
  6. Replies
    4
    Views
    18

    Re: 1976/1977 Mercury 1150

    Yes---76 and 77 were very similar decals.------So what is your serial number ?-----Visit ---nymarine decals.------To see the samples.----Decals are listed for models with and without power...
  7. Replies
    4
    Views
    18

    Re: 1976/1977 Mercury 1150

    Edited
  8. Replies
    15
    Views
    99

    Re: 1976 Johnson 35hp starter solenoid issue

    These starters are so easy to take apart for inspection / new brushes !!!
  9. Re: Motor stalling on 2005 Johnson 90hp outboard

    I do not believe there is a shift interrupter switch on V-4 models !
  10. Re: Broken cavitation plate question Honda BF 135

    ???----It is much easier to put a piece 1/4 or 5/16" aluminum plate onto a milling machine to do the recess for the trim tab BEFORE the main welding.-----90% of the work done and 10% finishing after...
  11. Re: Broken cavitation plate question Honda BF 135

    ??----Hard to believe the lack of experience sometimes I say.
  12. Re: Broken cavitation plate question Honda BF 135

    Machine the recess for the trim tab ----BEFORE ----The welding.------Just had welding like that done on an Evinrude V-6 gearcase.------Go fast " lightning " gearcase.-----No way would I buy a new one...
  13. Replies
    19
    Views
    128

    Re: 1989 Johnson GT150 - Power Trim & Tilt

    Aluminum oxide has to be scraped out.-----A sealer can be used to keep air and water out of the areas where the build up occurs.-----That is if in fact jammed bushings are the problem.
  14. Replies
    1
    Views
    33

    Re: Original Factory Manuals

    EU -----Tells me your motor is a 97 model.------And 1993 and newer would all be the same manual.
  15. Replies
    3
    Views
    67

    Re: Johnson 15 Opinions Is this fixable?

    Easy fix here in southern Ontario.-----evinrudeparts.ca-----May be able to assist you.
  16. Replies
    10
    Views
    105

    Re: What is this kind of part?

    Where did you find this part ?----Did it come out of the oil pan ?----Or was it just laying around in the lower cowling ?
  17. Replies
    4
    Views
    51

    Re: 1968 Evinrude 3 hp starter

    Many different model numbers but all use the same starter.------JH23 or JW23 would be an example.----The 1968 were the first year with the fiberglass cowling.----That starter on the side of the...
  18. Replies
    16
    Views
    122

    Re: 3 Evinrude Fisherman 5mph full throttle

    There you go.-----You said that motors run ---" great "-----But now we know there are issues.-----Pull the flywheels.----Inspect ignition coils.----You will find 2 new coils or ones that are old and...
  19. Replies
    19
    Views
    128

    Re: 1989 Johnson GT150 - Power Trim & Tilt

    Oxygen JOINS with aluminum to form ALUMINUM OXIDE.----That is the white powder that you might see.----So with oxygen joining up there is more material in the holes than before.------That is one...
  20. Replies
    16
    Views
    122

    Re: 3 Evinrude Fisherman 5mph full throttle

    I have to agree 1 cylinder.------But he says that they all run " great " so how could it be that all 3 are running on one cylinder?-----A shop with a test prop could quickly determine condition of...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4