Logo

Search:

Type: Posts; User: stang32

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. 89 omc, cobra very hard to shift to neutral

    ok, so this boat has a new cable, fully adjusted with factory tools, the shift interupt switch is operating as designed, the micro switches as well, when in reverse and going into neutral the shift...
  2. Re: seriously need some experts help on this one, no water exiting manifolds

    1a305748
  3. seriously need some experts help on this one, no water exiting manifolds

    ok, so i had a post earlier about this but i want to consolidate. this is a 2004 5.7 MPI. bravo set up. with standard cooling system with no upper hoses to the elbows the boat came to me overheating....
  4. Re: 2004 merc 350 mag mpi high temps on new dry joint manifolds, one thing after another with this b

    ok, update time, today i replaced the raw wter impeller, the manifolds still overheated, then while the engine was off, i removed the drain plug from the thermostat housing and the amount of pressure...
  5. Re: 2004 merc 350 mag mpi high temps on new dry joint manifolds, one thing after another with this b

    it has the right restrictor gaskets that is for sure.
    yes i know what a thermostat does, and its doing its job,
    thats 1 thought, and why i am pulling the drive later today i will check for the...
  6. Replies
    2
    Views
    188

    Re: 4.3 tks stalls while trying to plane

    does it dye when accelerating in neutral or only in gear? check the fuel pressure readings
  7. Replies
    2
    Views
    171

    Re: 4.3 MPI Diagnostic Readings for no start

    spray some starting fluid into the throttle body, if it kicks, then you know its fuel related,. could be an ecu issue, did the scanner show any fault codes?
  8. 2004 merc 350 mag mpi high temps on new dry joint manifolds, one thing after another with this boat

    have an issue where this boat has readings on new manifolds and riser of over 180 degrees,
    back story ,the boat was overheating terribly and the previous owner had another mechanic run tests where...
  9. Re: anyine got an easy way to flush a p/s system of water?

    No, that would be silly, why would you think that?
  10. Re: anyine got an easy way to flush a p/s system of water?

    yeah, i know, the fact is, the water came into the bilge in under 1 hour due to a broken hose clamp on the lower fitting on the manifold then the bilge pump was clogged so it was working but not...
  11. anyine got an easy way to flush a p/s system of water?

    i have a boat that took on a lot of water due to a broken bilge pump, it got up to the top of the p/s pump. the system has quick connects on the steering rack so that may make things easier. anyone...
  12. Re: looking for an alternative to 8M6000623 - water pressure Sensor

    yes, i am aware of all the garbage ones out there and thats why i was seeking out a genuine GM sensor. BTW, new list price is 190 for this sensor. yes i can find it cheaper but even at my cost,...
  13. looking for an alternative to 8M6000623 - water pressure Sensor

    I know this is a GM sensor but i can not find the right one. i got an ac delco 12677837 but the thread size is 3/8 and the sensor i pulled from the engine is 1/4"
    this is the sensor that reads the...
  14. Re: looking for measurements for v/p sx-a trim pistons

    edchris, thanks for the input but that is not the issue.

    thanks dave,

    chris, this is news to me, i wonder why they would be a shorter travel cylinder. next question is , how can i identify...
  15. looking for measurements for v/p sx-a trim pistons

    i have a 2009 v/p and believe the trim pistons are not going to full extension and was hoping someone out there with the same setup could give me a measurement from center of pin to center of pin. i...
  16. any tips on replacing the prop shaft seals on a dp-sm outdrive?

    ii've read the manual, i have the spanner tool to remove the retainer from the case but it looks like i need the puller to pull the outer shaft from the drive. which i do not have/ anyone have a...
  17. loooking for a manual for a duo prop outdrive, i need to replace prop shaft seals

    does anyone have access to a manual on line? i need to replace the seals in the carrier and between the 2 shafts and i have never done a duo prop before.
  18. Replies
    8
    Views
    404

    Re: Hello please read and help

    thats alot to absorb. the thing that jumps out at me is the tthe boat ran fine the 1st time out except for the water intrusion, so why would the timing and dwell be off now?
    you can do both hooked...
  19. Replies
    1
    Views
    240

    can anyone identify this shift assy?

    i need to get parts and maybe a whole replacement but i 1st need to identify the model.
    the upper shifter cable has a lot of play in it and wilo not shift into forward, only reverse. the lower...
  20. Re: any ideas on getting a starter out of a 5.7 when the bolt heads are stripped studs frozen?

    yeah, i agree, now i just have to sell the owner of the boat to give me the green light, i think she is all but done withe this boat as it is.
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4