MarineEngine.com - Your online store for all types of marine engines and boat parts.
PHONE ORDERS
Monday - Friday
9:00 AM - 5:00 PM EST
Click for TOLL-FREE Number
Online Checkout
Special $9.95 Flat Rate Shipping
(800) 209-9624 | Home | Contact | Shipping | Returns | Cart View your shopping cart.
Part Number Search
Shop by engine/drive part number.
Original & matching parts for sale.
Manuals & Accessories
Shop by description, item number
or manufacturer's model number.
Boat Repair Forum Boat Repair Forum   Boat Video Gallery Video Gallery
   

Search:

Type: Posts; User: jknoah

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    3,451

    Re: ESKA 5HP Flywheel Removal

    I don't know what model of ESKA engine he has, but My ESKAs are 1968,1967 5 HP single cylinder air/water cooled motor. In the starting instruction,It says mix 1/2 pint of S.A.E oil to a gallon of...
  2. Replies
    3
    Views
    895

    Re: convert tiller motor

    Ok, here is the number . BF8A motor ,# BZBC 1500205 .
  3. Replies
    3
    Views
    895

    convert tiller motor

    Hello everyone, I have a old 8 hp tiller motor, Honda BF8 ,I think 1999 or 2000 engine.
    Is it possible this one to convert a remote control motor for throttle, shift, steering,engine start ...etc ?
  4. Replies
    9
    Views
    3,451

    Re: ESKA 5HP Flywheel Removal

    1:25 oil mix like a chain saw
  5. Replies
    9
    Views
    3,451

    Re: ESKA 5HP Flywheel Removal

    No luck. I give a several rap on the flywheel nut while gently pressing the underside of the f.wheel , It doesn't move a bit. I should make a tapping the holes and use a balance puller .
  6. Replies
    9
    Views
    3,451

    Re: ESKA 5HP Flywheel Removal

    Thanks for quick response .Yes, there are three small holes on top. What is the "proper tool "? Can I get it from auto parts store? How does it work? just pop it up or turn to loose it? / ...
  7. Replies
    9
    Views
    3,451

    ESKA 5HP Flywheel Removal

    Hello,I'm fixing an old Eska 5hp motor, I do not know built year but model# 1195. I guess its been made around 60'~70's. My issue is that how to remove flywheel? I need to replace contacts or coil...
  8. Replies
    0
    Views
    973

    kick back 9.8hp Mercury 1973

    Hello everyone ,I recently purchased a 73' 9.8 Mercury outboard.I cleaned the carb. and put new plugs. It starts and runs fine at first but then it kicks back every 2,3 second. The cylinder...
  9. Replies
    2
    Views
    1,866

    Re: How to clean carb needle valve

    Thanks for your opinion, I'll try it tomorrow
  10. Replies
    2
    Views
    1,866

    How to clean carb needle valve

    Hello , Recently I purchased a used 8HP honda outboard . With this engine#(BF8A,BZBC-1500205) I think It is 2000 model. It seems like not cared for a few years so I try to clean carb but I can't...
  11. Replies
    11
    Views
    1,339

    Your shift cam has installed w

    Your shift cam has installed wrong way (upside down)in the LU.
  12. Replies
    12
    Views
    1,015

    "JB, all cylinder compression

    "JB, all cylinder compression has in good range. The readings are between 124-126lb."
  13. Replies
    12
    Views
    1,015

    "Noel ,You say "there shou

    "Noel ,You say "there should be a good flow of fuel out of the pipe" Well,what do you mean that PIPE?
    This motor doesn't have a separate fuel pump like a more older Mercury(I see 73' or more older...
  14. Replies
    12
    Views
    1,015

    I tried but the low speed idle

    I tried but the low speed idle screw didn't improve the starting problem so I'm going to try Noel's solution tomorrow.
  15. Replies
    12
    Views
    1,015

    "Hello, Noel I already checked

    "Hello, Noel I already checked fuel pumps(there are two carbs and each carb has its own diaphragm )but I couldn't see any damages.And You say fuel pressure and sticky reeds? Could you explain how to...
  16. Replies
    12
    Views
    1,015

    "Low speed idle adjustment,It

    "Low speed idle adjustment,It could be the solution I didn't think about that. I'll test the motor tomorrow and let you know result. thanks for your advice ,Tom and Brian."
  17. Replies
    12
    Views
    1,015

    "Hello, I need someone's h

    "Hello, I need someone's help or may be Mr lamb or Noel can help.The issue is starting problem . My 4 cylinder classic 50 won't start by itself but only it starts with spit of mixed gas. However,...
  18. Replies
    16
    Views
    974

    "I purchased a tach module fro

    "I purchased a tach module from EBAY. It's a NOS and cheap, paid $20 for it. The seller said before 86' all Merc 4-cylinder motors(thunderbolt ,lighting energizer) require this module for a tacho...
  19. Replies
    16
    Views
    974

    "From EBay I found a similar t

    "From EBay I found a similar tach meter but this one has a tacho module(see pic).Because lack of this ,My tacho does not work? http://www.marineengine.com/discus/messages/12479/289539.jpgtacho...
  20. Replies
    16
    Views
    974

    "Noel, still it doesn't wo

    "Noel, still it doesn't work. I followed up what you said. I checked wiring between the motor(switch box,rectifier) and control box and no problem found.When I turn the key on , the white(+) and...
Results 1 to 20 of 41
Page 1 of 3 1 2 3