Logo

Search:

Type: Posts; User: racerone

Page 1 of 4 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    1
    Views
    7

    Re: 2.2 Mercury Parts Help

    Serial number of the motor ?----Your location ?
  2. Replies
    1
    Views
    6

    Re: Mercury 9.8 Switch box Problem?

    The 7.5 and 9.8 are essentially the exact same for a given year.----The 9.8 has slightly bigger intake transfer ports in the side of the block.
  3. Re: Exhaust Holes in 1968 3hp Johnson JHL-23M

    Sounds correct with just some water misting out.----If you do not know the condition / age of the impeller you should install a new one.
  4. Re: assembling 1965 evinrude big twin impeller...

    Well-----Post #10 clearly says that water MUST be 6 to 8" ABOVE the impeller !!!----Make it so.
  5. Replies
    3
    Views
    23

    Re: check for spark

    Model # is ?------Be very careful if you start applying volts in various places.---Mistakes can be expensive.
  6. Re: 1988 90 Hp Johson just not getting enough fuel- Model J90TLCCA

    Some will argue.----If your compression test numbers are accurate you perhaps need to take one cylinder head off for inspection of cylinders.-----Compression is way to low.------Mere pennies for a...
  7. Re: 1989 Mercury 20 2 stroke vaccuum issues?

    Test run with another fuel tank.
  8. Re: Test Wheel for a 1989 Evinrude 90 HP E90TLCUR

    There are many tests and inspections you can do to determine the condition of your motor.------What did you find on yours that might be the culprit ?????
  9. Re: Test Wheel for a 1989 Evinrude 90 HP E90TLCUR

    ???---Propshaft was the same on V-4 motors from about 1970 to 1998 and even beyond that !!
  10. Replies
    27
    Views
    5,988

    Re: Forward and Reverse Backwards

    You can not switch the way the motor shifts with a different control box.
  11. Re: 1994 OMC Turbjet confusion (evinrude/Johnson 115)

    If in Canada---Your location ?
  12. Re: 1975 Evinrude 15hp outboard 15555C crushed copper water tube!

    The correct way is to remove powerhead and install a new tube with new grommet.----Careless work on some ones part leads to much more work to correct the error.
  13. Re: assembling 1965 evinrude big twin impeller...

    They usually stay up in the exhaust housing.----You MUST first install them in the exhaust housing.----Then install the lower unit !----No need to test with a drill.----It is hard to assemble them so...
  14. Re: Test Wheel for a 1989 Evinrude 90 HP E90TLCUR

    You need to accept the fact that a test wheel ( test propeller ) is the same year after year !!!-----Or do you doubt that the 382861 will work for your motor.------Sorry , if I come across as BLUNT...
  15. Re: Test Wheel for a 1989 Evinrude 90 HP E90TLCUR

    Well---Not sure what manual you are perusing.----My factory manual for V-4 crossflow engines lists.-------OMC part # [email protected] 4800 RPM minimum.----And I thought an E90TLCUR was an 87 model ??
  16. Re: Test Wheel for a 1989 Evinrude 90 HP E90TLCUR

    Edited
  17. Replies
    27
    Views
    5,988

    Re: Forward and Reverse Backwards

    Correct----The linkages off a 73 or 74 can be adapted.------When dealing with 2 cylinder lower units you need to check condition of it.----They are not robust.------If in...
  18. Re: Evinrude Skipping: What do you guys think this is?

    Perhaps you have run it like that for a while.----Stop running it.------Check gear oil.----Test for spark that can jump a gap of 7/16" on all leads.----I would take lower unit of to check shift rod...
  19. Replies
    3
    Views
    73

    Re: carb and fuel quesions

    Sorry ---there are no idle mixture screws on those carburetors.
  20. Replies
    40
    Views
    418

    Re: Lower Unit Bearing Replacement

    I believe that is for shipping / storage only--------A wise person would remove that plastic piece !!
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4