Logo

Search:

Type: Posts; User: daves69

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    23
    Views
    221

    Re: 73 Chrysler 318 rebuild

    Here's some help for your budget............
    https://www.manualslib.com/manual/1007590/Chrysler-Lm-318.html
  2. Replies
    23
    Views
    221

    Re: 73 Chrysler 318 rebuild

    Be aware there are differences between the 318 and 360 blocks (aside from bore/stroke) you'll encounter should you go that route.
  3. Thread: Lm318bwr107440

    by daves69
    Replies
    2
    Views
    74

    Re: Lm318bwr107440

    .........
    http://www.marineengine.com/boat-forum/showthread.php?456449-Chrysler-Marine-318-free
  4. Replies
    7
    Views
    160

    Re: Replace intake manifold?

    Not sure, but I believe the ports on a 273/318 may be smaller than the 340/360.
  5. Replies
    4
    Views
    122

    Re: Minnkota shaking,slows, and stops

    You need a bigger oar! :)

    Some basics...….
    https://themarinebattery.com/trolling-motor-troubleshooting-tips/
  6. Re: Someone put water in my gas tank! Lm318 I cleared it, it ran, now it only cranks. What to do?

    Lol,
    I have always run ethanol fuel in my carbed '08 VP since new. I do add Stabil. After months of layup, a few pumps of the throttle, it again cranked right up this year.


    Maybe 3(?) years...
  7. Re: Someone put water in my gas tank! Lm318 I cleared it, it ran, now it only cranks. What to do?

    ……………...
  8. Re: Someone put water in my gas tank! Lm318 I cleared it, it ran, now it only cranks. What to do?

    ……….
    https://www.goldeagle.com/brands/heet/
  9. Re: Someone put water in my gas tank! Lm318 I cleared it, it ran, now it only cranks. What to do?

    With ignition OFF, is the carb pump supplying fuel or water or nothing at all when the throttle is pumped?
  10. Replies
    9
    Views
    439

    Re: VP 3812269 Steering Actuator

    Yeah, Calling it a done deal...……….for now! No leak yet. Need to put it in the water yet!
    A picture of the original (leaker, center) and the 1st "Kit" seal that is too small on the OD (far right). ...
  11. Replies
    5
    Views
    218

    Re: 4.3 Volvo penta hard start

    Just some basic stuff after you've eliminated the ignition.
    A Holley carb?
    Evaporation maybe a sign your engine is heating up now more than previously.
    Fuel bowl leaking down? Black smoke / rich...
  12. Replies
    16
    Views
    410

    Re: Checking Coils and CDI

    some test procedure………
    https://www.outboardparts.com/chrysler/miscellaneous/troubleshootinghelp.htm

    maybe a source for parts...……
    http://standardmagneto.com/Marine/forceparts.html
  13. Replies
    5
    Views
    266

    Re: Need help with tilting mechanism

    Lever at the top..........
    20687
  14. Replies
    5
    Views
    266

    Re: Need help with tilting mechanism

    I can't tell if you have a reverse latch/unlatch lever for manual tilt. Possible someone took the power tilt/trim? I can't imagine taking the manual tilt stuff unless the goal was to swap in power...
  15. Replies
    9
    Views
    439

    Re: VP 3812269 Steering Actuator

    Update O-Ring Store seal. Closest they had was a Metric 16X24X5. A video I watched mentioned this seal. It went in although
    it's actually big on the OD for the cylinder. No leak so far though....
  16. Replies
    9
    Views
    439

    Re: VP 3812269 Steering Actuator

    Well, my first seal source sent the wrong ram seal in their kit. Too small on the OD and too short on height. Ram diameter is right. They'll be getting this kit back!
    Trying singles ordered from The...
  17. Replies
    8
    Views
    412

    Re: LM 318 running rough over 2500 rpm

    I do agree Rick. That is the reason I mentioned "
    I'm sure he could match a pair of marine distributor curves if one is good to base off of.":)
    I do know a pair of aftermarket distributor curves...
  18. Replies
    9
    Views
    439

    Re: VP 3812269 Steering Actuator

    Thanks for the reply.
    I'm game for rebuilding it myself. It's the actuator remove and install that's a PIA! I went ahead and ordered the ram seals. Plunger has a crack, rod is fine though.
  19. Replies
    8
    Views
    412

    Re: LM 318 running rough over 2500 rpm

    You might want to lubricate the distributor advance mechanisms even if it's not the cause of your symptom. I'd guess they are overlooked in tune ups by most. Even the automotive mechanics omit it.
    ...
  20. Replies
    9
    Views
    439

    VP 3812269 Steering Actuator

    My '08 actuator decided to leak out over the lay up. Not serviceable?? Seems to be a fairly common fail for these. At 600 or more for a "new" replacement I'm looking at why I would not try to...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4