Logo

Search:

Type: Posts; User: flyingscott

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Re: Gear case Broke on Johnson 175 FICHT 1998

    Go to the SEI marine products website I bet they are competitive and it is a new product.
  2. Re: Possible Intermittent Timing Problem

    Did the screw come loose on t timing tabs? Did the adjustment on the carbs change? Air leak in the manifold? Air leak anywhere?
  3. Replies
    2
    Views
    25

    Re: 4 cyl not working together

    That is a 2+2 motor as it idles on cylinders 1 and 2. The other 2 kick in at 1800 rpm as was mentioned above. They accomplish that by not having idle circuits in the bottom 2 carbs. They only allow...
  4. Re: Really weird problems 1982 2 stroke 60hp Evinrude

    If the timer base is sticking then the link and sync is off and the carbs and timing no longer work together. That needs to be cleaned that should move as fast as the throttle moves. The max timing...
  5. Re: Really weird problems 1982 2 stroke 60hp Evinrude

    If the timer base is jumping to catch up that needs to be addressed. It should move smoothly with the throttle until it hits the max timing stop. That carbs should keep moving after the timer hits...
  6. Replies
    6
    Views
    55

    Re: 2001 Mercury 115 not holding prime

    First thing is to buy the Correct Mercury Factory Manual. Yes you can do the compression and spark test yourself. Most auto parts shops now have loan a tool and the spark tester is around $10. You...
  7. Re: 2000 Evinrude 225 thrust washer to go with Solas prop

    Call Solas and see if you need their thrust washer.
  8. Replies
    7
    Views
    73

    Re: Starting Issues

    Take the starter apart and clean it. You do not want oil on thew pinion it attracts dust and gums them up.
  9. Replies
    6
    Views
    55

    Re: 2001 Mercury 115 not holding prime

    Check spark and compression.
  10. Re: 1987 225 johnson tach jumps around at idle

    How much does it jump? Is the new tach set right? My cheap tach will jump 100-150 rpm at an idle just because the way the pulses work.
  11. Replies
    3
    Views
    31

    Re: Mercury 60hp 1989 lower unit

    The drive shaft always turns in the same direction so it cannot do what you say, Unless it is stuck in one gear. In forward the prop should ratchet one way and lock in the other. In reverse it locks...
  12. Re: 2003 90 h.p. 2 stroke Model #1090412AD hard starting, smokes

    How long have you owned this motor? Are you sure it is not flooding from fuel? May just be the check valve in the line is bad. If you have to tilt the motor up to start it there is something wrong...
  13. Replies
    12
    Views
    111

    Re: sparks per revolution

    Yes, you will be lugging the motor. What boat is this on? Are you positive your tach is correct?
  14. Replies
    5
    Views
    48

    Re: 15 hp 1977 mariner fuel connection

    You have a Yamaha built motor maybe look at Yamaha connectors. They are similar to OMC connectors but not the same. Put up a pic of this double line that your dealer said you had. Maybe find a new...
  15. Re: Help me identify which electrics are missing from this stripped 1977 Evinrude 35?

    Good luck with your motor.
  16. Re: Johnson/Evinrude 8hp J8REUC Fuel Consumption

    Revisit your carb work and make sure everything is clean. Did you replace the needle and seat? Float level correct? Manual primer not leaking by?
  17. Re: Help me identify which electrics are missing from this stripped 1977 Evinrude 35?

    The only thing it looks like you are missing is the ignition coils. You should be replacing the forward gear also. The shift rod bent because it was jumping out of gear. The bushings wore out because...
  18. Replies
    12
    Views
    111

    Re: sparks per revolution

    Your manual should say 5-6000 rpm and you want to be propped for closer to 6.
  19. Re: What's the low down on the throttle linkage? 1995 115

    Get the manual for your motor. The 2+2 motors are quirky and it does not take much to screw them up.
  20. Replies
    14
    Views
    109

    Re: finding tdc on 2000 70hp jhonson

    Then take the.piston stop out and rotate the piston past top dead center. Then put the.piston stop back.in.
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4