Logo

Search:

Type: Posts; User: crashband

Search: Search took 0.00 seconds.

  1. Replies
    32
    Views
    15,405

    Re: Chrysler 318/360 Marine Inboard Starter

    Thanks Ricardo!
  2. Replies
    32
    Views
    15,405

    Re: Chrysler 318/360 Marine Inboard Starter

    I picked up a IMI Hi-torque starter not too long ago to replace the old style bendix drive. The new one has an extra post to the solenoid whereas the old one just had the post to to ignition.

    Here...
  3. Replies
    32
    Views
    15,405

    Re: Chrysler 318/360 Marine Inboard Starter

    Just got the new starter in today. It has an extra pin by the main cable post which is suppose to go to the starter solenoid. Where should I jump the cable to? Would it be to ignition 1 or 2 on the...
  4. Replies
    32
    Views
    15,405

    Re: Chrysler 318/360 Marine Inboard Starter

    Not to bring an old thread back from the dead, but this is very much relevant.

    My bendix starter finally decided to give up the ghost. Currently looking around for alternatives and see the new IMI...
  5. Replies
    3
    Views
    1,157

    Re: Bench Starting 318 Electric Ignition

    Thanks for the suggestions. Will try to get her started tomorrow
  6. Replies
    3
    Views
    1,157

    Bench Starting 318 Electric Ignition

    Hi all,

    I have a 225HP Chrysler 318 with electric ignition that I would like to start on a bench? Does anyone know how to wire it up for a simple bench start?
  7. Replies
    2
    Views
    1,053

    318 Fuel line

    Hello all,

    Does anyone know if there is a aftermarket fuel line that runs from the fuel pump to the carb that isn't copper? I need to find a replacement and can't find anyone or anywhere that...
  8. Replies
    1
    Views
    9,394

    Re: walter rv30 remote

    pm sent
  9. Replies
    0
    Views
    456

    Correct Transmission output?

    Hey guys,

    Still having ALOT of trouble understanding rotation on engines so was hoping someone could point me in the "right direction".

    Had a reverse rotation 318 (single screw) that had a 1:1...
  10. Replies
    11
    Views
    700

    Re: Chrysler 318 Inboard ersions

    Hey Guys,

    Looking for a little input on this subject here....

    I went ahead and started taking apart the raw water cooled LM318 today. According to the firing order, it seems that I have a RH...
  11. Replies
    16
    Views
    1,128

    Re: 318: water blown out of spark plug holes!

    Hey Brooks,

    What kind of fuel tank did you install?
  12. Replies
    11
    Views
    700

    Re: Chrysler 318 Inboard ersions

    Thank you Dave!! this explains it perfectly!!!!!! I actually thought I was looking for the top ridges and not the bolt pattern nor the "wave"/scalloping (didn't know that was what scalloped meant)
    ...
  13. Replies
    11
    Views
    700

    Re: Chrysler 318 Inboard ersions

    How would I be able to spot the differences externally?

    The reason I ask is that I will be looking at a FWC engine this weekend but the seller has no idea as to what year it is aside that for the...
  14. Replies
    11
    Views
    700

    Re: Chrysler 318 Inboard ersions

    Thanks fastjeff.

    Regarding the M318, LA318 and LM318's were there any differences amongst them?
  15. Replies
    11
    Views
    700

    Chrysler 318 Inboard ersions

    Good evening Gents,

    I currently have a raw water cooled electronic ignition LM318 connected to a v-drive in a 79 Silverton 26' Flybridge. Due to neglect from the PO, the exhaust manifolds, risers...
  16. Replies
    3
    Views
    666

    Re: Chrysler 318, RH or LH ?

    This thread might be of some assistance:

    http://www.trojanboats.net/wforum/viewtopic.php?t=5712
Results 1 to 16 of 16