Logo

Search:

Type: Posts; User: jafa39

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: Turbojet query

    by jafa39
    Replies
    6
    Views
    682

    "Has no impellor, runs off the

    "Has no impellor, runs off the turbine...no impellor shown on BRP parts diagrams."
  2. Thread: Turbojet query

    by jafa39
    Replies
    6
    Views
    682

    "Thanks Martin, boat has no ma

    "Thanks Martin, boat has no manual but that start up procedure makes sense and it has the same turbine fed cooling system.....thanks heaps!"
  3. Replies
    2
    Views
    1,181

    "Check play in the crank befor

    "Check play in the crank before assembling, otherwise it should be good to go."
  4. Thread: Turbojet query

    by jafa39
    Replies
    6
    Views
    682

    Does anybody here have any exp

    Does anybody here have any experience of OMC Jetboat motors? Its a 1996 115HP V4 VRO and it filled up the bottom 2 cylinders when sitting with the flush hose running but the motor not...
  5. Replies
    23
    Views
    617

    Chuck it in a tank of diesel f

    Chuck it in a tank of diesel for 3 months...its an old vintage bike restorers trick.
  6. They are in the manual usually

    They are in the manual usually.
  7. Replies
    1
    Views
    1,137

    "A good flush through with a s

    "A good flush through with a salt inhibiting solution via muffs, some 2-strok oil down the plug holes and drain the carbs of fuel will suffice. Plus a good overall soaking (especially under the hood)...
  8. Replies
    2
    Views
    550

    "Take them to court, the whole

    "Take them to court, the whole point in paying for the pump to be done is to prevent a blow up.....they are taking the weewee mate."
  9. Replies
    5
    Views
    1,096

    "First of all, put some 2-stro

    "First of all, put some 2-stroke oil down the plug holes and check that it turns over when you pull the cord. Then, check it has compression.

    If it does then take the carbs apart and clean them...
  10. Replies
    2
    Views
    478

    Ebay might turn up a 2nd hand

    Ebay might turn up a 2nd hand one.
  11. Replies
    2
    Views
    584

    "Get a price from Suzuki for t

    "Get a price from Suzuki for the parts and then add your life savings for labour....no seriously, should be a coupla hours but they may want to do a diagnostic check first and that will add an hour...
  12. Thread: What a Mess

    by jafa39
    Replies
    2
    Views
    405

    You can helicoil the plug thre

    You can helicoil the plug thread...I have done them without taking the head off.....needs lotsa grease and care.
  13. Replies
    5
    Views
    7,984

    "Compression check first and f

    "Compression check first and foremost, you may need to bribe your local car mechanic to help you with this...they should be above 100 and within 10% of each other....120+ is good.

    Dunno if you...
  14. Thread: 1970 prop

    by jafa39
    Replies
    1
    Views
    8,852

    Tried Ebay???

    Tried Ebay???
  15. Replies
    5
    Views
    7,984

    Might be compression is low or

    Might be compression is low or a crank seal is stuffed....could be carbs...run all the comp tests before spending any money.
  16. Replies
    3
    Views
    8,543

    "They didn't change much i

    "They didn't change much in the 70's, the manual I had covered all you need to know...was a Clymer manual."
  17. Replies
    3
    Views
    8,543

    "You need a timing light to ch

    "You need a timing light to check the timing properly, start by adjusting all the linkages as per the manual.

    Check timing at idle and at full advance (WOT)...maybe someone here can give you the...
  18. Thread: 2 hp envirude

    by jafa39
    Replies
    3
    Views
    480

    "Revs up before it dies out as

    "Revs up before it dies out as the fuel mixture gets very lean just before it runs out completely.

    You may have two problems here, one faulty impellor and a fuel issue. Check the impellor first....
  19. "The conversion would involve

    "The conversion would involve the entire pivot/clamp assy as the piston you have is gas filled and the tilt/trim is hydraulic/electric.

    The research I have done indicates that it is better to...
  20. Replies
    3
    Views
    900

    "Bigking, best to start a new

    "Bigking, best to start a new thread as it will likely get more views.

    The shifter rod disconnects up under the carbs, its a tight squeeze to see it.

    Don't forget the hidden bolts under the...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4