Logo

Search:

Type: Posts; User: crankbait

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Re: Need advice on transom repair - with images.

    should have done your research, BEFORE, you started cutting......
  2. Thread: Pictures

    by crankbait
    Replies
    4
    Views
    3,178

    Re: Pictures

    i use tinypic with zero problems....(it is free)
  3. Replies
    1
    Views
    628

    Re: Dumb question please help!!!

    for the sake of speed......run it by the yahmaha dealer
  4. Replies
    4
    Views
    294

    Re: Does anybody have a Yamaha F20?

    the engine can be transported/stored on its' throttle arm side. (as per owners manual). my measurement under the cav plate is 1 1/8 thick
  5. Replies
    20
    Views
    2,085

    Re: Cannot Idle under 1500 - 1800 RPMs

    just curious.......when you are done for the day, do you disconnect the fuel line and run the carbs dry, or do you just shut the engine off and walk away ? i am not being cynical.
  6. Replies
    6
    Views
    591

    Re: Oil Change question

    when it comes to oil and water filters......bigger is always better !
  7. Replies
    6
    Views
    805

    Re: 04 4HP carb lacks vacuum ports

    no. cap each one off individually
  8. Re: Vibration from mount failure or timming issue

    bring it up to TDC......., pull the cap off and look where the rotor is pointing. that is number one. (if you did not pull the distributor). even if you did, and it is at TDC, but pointing in a...
  9. Replies
    24
    Views
    1,147

    Re: points burnout

    Here is schematic for a 12 DC system with an Earth Ground.
    Make sure that you drive the grounding rod into the earth at a depth of approximately 8 feet.

    .....ricardo.....THAT....is funny !!
  10. Replies
    7
    Views
    1,349

    Re: DF70 blows oil filter gasket out

    next step would be to put a mechanical oil gauge and see what it reads when the blow out happens. you may have a bad oil pump.
  11. Replies
    7
    Views
    1,349

    Re: DF70 blows oil filter gasket out

    i would take the filter off, and make sure that the old oil filter gasket is stuck to the block.
  12. Replies
    13
    Views
    718

    Re: new guy maybe stupid question.

    treat it like a handgrenade........pull the pin, and toss it !!
  13. Replies
    5
    Views
    388

    Re: Carburetor kit questions

    always......go with a oem kit. they are a little pricer, and you are getting parts that are made to oem specs.
  14. Re: Please advice on homemade dive plateform can I JB cold weld glue

    I do not like the idea of exposing a fuel supply to possibly immersed I water.
  15. Replies
    5
    Views
    4,949

    Re: Outboard Fuel Pump Repair

    no sealer
  16. Re: Help! What is the difference in these two props?

    both props will work. the cp1 prop is a aftermarket prop, and the a45 prop is oem merc prop.
  17. Re: new starter for 351w - 9 tooth. Can magnets loose their strength?

    https://www.dbelectrical.com/ i bought a new style starter from these people that was lower priced, and was fantastic at stating my volvo penta !!
    this is a great source for you guys !!
  18. Re: 200TXL76; Johnson OUTBOARD Need a mechanic

    call wrights marinine in lodi.....they work on fish and game boats. i live in sacramento, and the drive is worth it for quality, honest work. 209-333-7855
  19. Replies
    12
    Views
    568

    Re: 100 hour service creates problems

    no.....sparkplug wire not installed correctly/damaged, wrong plugs installed.....gapped wrong. NOT normal !
  20. Thread: Christmas

    by crankbait
    Replies
    3
    Views
    1,084

    Re: Christmas

    http://i65.tinypic.com/9ux3r9.jpg
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4