Logo

Search:

Type: Posts; User: shakey

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds; generated 47 minute(s) ago.

  1. Replies
    3
    Views
    1,625

    Re: Identifying a pre 1970 4.236

    Hi Rob. I would say that the info you have dates the engine pre 1967 as they where originally fitted with a generator charging system. As mentioned any large rural tractor parts supplier should be...
  2. Replies
    3
    Views
    1,625

    Re: Identifying a pre 1970 4.236

    G'day Rob,
    You mention in your post it has a Alternator if this fitting is std it dates post 1967.,pre 1974 motors are fitted with Lucas M50 Starters & 2 bolt fuel lift pumps & 1rope...
  3. Replies
    1
    Views
    1,469

    Re: perkins 6 cylinder engine

    Sounds like you may have a leaking exhaust manifold or a cracked head. Remove exhaust manifold and look for water trail mark if none pressure test.
  4. Replies
    1
    Views
    8,742

    Re: Compression tester for 2712e & new injectors

    G'day,
    What part of the WORLD are you in? Do you need new holders or only nozzles?
  5. Re: 1977 MD11C - Trick to bleeding the engine after fuel filter change

    G'day,
    Most small engine lift pumps start struggle with lifts of over 4'. You may want to look at fitting a outboard type priming bowl in the circuit close to the lift pump or a electric...
  6. Re: 1977 MD11C - Trick to bleeding the engine after fuel filter change

    G'day Carole,
    I have not read all the posts so a lot of this has possibley been suggested my opologies to those people. Start the bleeding process at the tank and work towards the...
  7. Replies
    24
    Views
    2,468

    Re: 4.107 spare parts in Hobart Australia.

    I'am pleased hear all your effort produced the outcome deserved. What a start to spring!!!! deserves a beer.

    Cheers, Shakey.
  8. Replies
    24
    Views
    2,468

    Re: 4.107 spare parts in Hobart Australia.

    There are 2 x 5/16''AF bleed scews to be found on hydraulic gov fuel pump one on the side and one on very top of the pump speeder adjustment screw be carefull not to undo the btm nut, bleed btm...
  9. Replies
    1
    Views
    1,796

    Re: Oil In exhaust manifold & turbo

    Take a look at the turbo oil drain piping sounds like you may have a blockage.
  10. Replies
    5
    Views
    1,134

    Re: 4-108m cooling problem

    G'day,
    This could mean that the affected cylinder has stopped at tdc not allowing the displacement area to open up or you may be dealing with a heat [thermal] affected crack or joint.
  11. Replies
    5
    Views
    1,134

    Re: 4-108m cooling problem

    G'day,
    As well as cooler seals and head it could also be the exhaust manifold they have a habit of leaking at the rear where the mixer connects. After next run remove the injectors once engine...
  12. Replies
    24
    Views
    2,468

    Re: 4.107 spare parts in Hobart Australia.

    G'day,
    DIecon engineering in Brisbane or All marine spares sydney may be able to help with a outlet elbow. You could try hand facing the old elbow and filling the damaged face with...
  13. Replies
    24
    Views
    2,468

    Re: 4.107 spare parts in Hobart Australia.

    G'day Shifter,
    For the studs try Gorringe, Tas engine reconditioners or Nuts & Bolts in Albert rd. Which heat exchanger and type of mounting do you have there are a couple of...
  14. Re: Can non-road enginse be used in marine applications?

    G'day,
    If your engines have come from a power generating back ground the fuel control govenor may require modifying for variable speed marine use, also bell housing adaption will need to be...
  15. Replies
    24
    Views
    2,468

    Re: 4.107 spare parts in Hobart Australia.

    G'day,
    Sounds like your perky has had a hard time. Which boat is it in ?. Try Keith Smith Box Hill rd Claremont may know of parts or have some. I get my parts from the The Rock Tractor...
  16. Replies
    24
    Views
    2,468

    Re: 4.107 spare parts in Hobart Australia.

    G'day Shifter,
    Whats the problem with the current rocker gear?
  17. Replies
    24
    Views
    2,468

    Re: 4.107 spare parts in Hobart Australia.

    The Pump Shed 15 Sunderland st Moonah will be able to source your jabsco parts.
  18. Replies
    24
    Views
    2,468

    Re: 4.107 spare parts in Hobart Australia.

    G'day,
    Gorringe reconditioning in nth Hobart can do any machine work and supply the listed parts. These are a wet liner engine so any water in lube oil could also mean liner seal or landing...
  19. Replies
    24
    Views
    2,468

    Re: 4.107 spare parts in Hobart Australia.

    G' DAY ,
    What parts are you after?
  20. Replies
    2
    Views
    1,270

    Re: Staring problem with 3GM30

    Sounds typical of air in the fuel system this could be be cause by any number of things . I would start checking filter seals,hose joints and fittings inc all bleeding point seal washers.This problem...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4