Logo

Search:

Type: Posts; User: kimcrwbr1

Page 1 of 4 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    7
    Views
    51

    Re: Boat will not plane out

    What is WOT rpm? If you get real high rpm you need to check clearance between the impeller and liner.
  2. Re: bearings and seal replacement Johnson RL2576

    I only see one driveshaft bearing and a thrust washer for the pinion. Is there another roller bearing just above the brass bearing for the pinion?
  3. Re: bearings and seal replacement Johnson RL2576

    A blind hole bearing puller may work for the upper roller bearing otherwise yes the flat bar and all thread method will do for the lower roller just be careful pulling the pinion you dont want to...
  4. Replies
    10
    Views
    55

    Re: power pack test

    Disconnect the kill wire at the pack. If that cure the issue you needto find the intermittent short. Be careful never apply battery pos to the kill wire it will cook the PP in a split second.
  5. Re: bearings and seal replacement Johnson RL2576

    Keep an eye on craigslist for a good parts motor. Your issue is only gonna get worse. You may get lucky and find a motor not running with a good gearbox for cheap. This is the time of the year more...
  6. Re: BF90 goes into limp mode at full throttle like clockwork

    There are too many factors that determine proper prop pitch. Use WOT rpm your model is between 5200and 6200rpm. Ideally you want around 5800 max with a light load. You can easily add three inches...
  7. Re: BF90 goes into limp mode at full throttle like clockwork

    The BF90 is rated at 90hp at 5800rpm. If you keep running at 6500rpm just start saving now for a new powerhead or a different motor. Your beating that one to death. If you want faster get a bigger...
  8. Re: BF90 goes into limp mode at full throttle like clockwork

    Your under propped if it goes over 6000rpm you can probably add three inches pitch safely.
  9. Replies
    7
    Views
    49

    Re: Volvo Penta DP 290 Problem. Need Help

    The PDS coupler could be the source of the grinding noise you would need to pull the engine for that repair?
  10. Replies
    7
    Views
    49

    Re: Volvo Penta DP 290 Problem. Need Help

    Do you shift into gear slow or fast? First off drain about half a quart of gearoil and then remove the shift mech from the upper gearbox. Is there metal shavings on the drain plug magnet? Inspect and...
  11. Re: 1971 Fastwin Gushing water out lower cowl.

    I would give it a good decarb now its running good. Get a can of seafoam spray and after the engine is fully warmed up take it to fast idle speed and spray the seafoam in the carb until it starts...
  12. Re: 1971 Fastwin Gushing water out lower cowl.

    If it is a new head gasket you should be OK 95psi is not that bad for rope start it should run just fine. Was there much carbon on the pistons.
  13. Replies
    2
    Views
    37

    Re: Help identifying 40 hp mercury

    I put it as a 1991 year is not important unless your looking for a manual you use the serial number to look up parts.
  14. Re: 1971 Fastwin Gushing water out lower cowl.

    Yea put some permatex aviation gasket maker in the recess then use a socket half the width of the welsch plug and gently tap it flat using the bolt side of the socket not the flat side. You may have...
  15. Re: 1971 Fastwin Gushing water out lower cowl.

    Is that with a rope pull or electric start on the compression?
  16. Replies
    25
    Views
    300

    Re: Power failure 40 HP

    Is there any wiggle up and down on the plate under the flywheel? Air gap between the flywheel magnet and coil is another possibility.
  17. Replies
    25
    Views
    300

    Re: Power failure 40 HP

    With the DVA cdi says min 200vac at cranking speed disconnected from the PP and 150vac connected for the charge coil. The ohms reading probably indicates a internal short in the coil. Replace the...
  18. Replies
    10
    Views
    152

    Re: 82 15 HP Evinrude - exhaust

    The 9.9 and 15hp models were the same in that era. Note to self give all grease zerts a good shot before winter storage!
  19. Replies
    10
    Views
    152

    Re: 82 15 HP Evinrude - exhaust

    There should be multiple years and hp for the parts you may need the first thing is take it apart to access the damage. Get the part numbers including gaskets and bushings. Is there a auto pilot...
  20. Replies
    18
    Views
    117

    Re: 1967 Johnson JH22C 3 HP run problems

    If those are the original coils just replace them now they will go bad if they are not bad already.
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4