Logo

Search:

Type: Posts; User: Bt Doctur

Page 1 of 4 1 2 3 4

Search: Search took 0.05 seconds.

  1. Re: How to remover water pump idler pully withseized to bushing and pinion stud.

    If the pully is seized to the bushing and the bushing is seized to the bolt, just cut everything off and replace with new
  2. Replies
    8
    Views
    76

    Re: Volvo Penta fuel issue

    except the high pressure and low pressure look exactly alike
  3. Replies
    6
    Views
    29

    Re: 1985 3.8 removal

    #35 V8 is the same
    https://www.l-36.com/pdf/manuals9/omc_7.png
  4. Replies
    6
    Views
    29

    Re: 1985 3.8 removal

    If you can get to the bottom of the dust cover and remove the bell housing bolts AND IF THE COUPLER IS NOT RUSTED TO THE INPUT SHAFT motor pull forward and up /out
  5. Replies
    6
    Views
    29

    Re: 1985 3.8 removal

    https://www.l-36.com/pdf/manuals9/omc_13.png
  6. Replies
    1
    Views
    40

    Re: Raw water inlet hose

    best bet is a good auto parts store and make one up .Doubtful after 60 years there is one in stock anywhere
  7. Replies
    6
    Views
    29

    Re: 1985 3.8 removal

    Depends, if a stringer ,you can just remove the engine ,on a Cobra you need to remove the drive first
  8. Replies
    6
    Views
    62

    Re: AQ171c Plug wire placement

    If you mean the flat cap ,stand by
    https://i.postimg.cc/MnQndvVH/original.jpg

    https://i.postimg.cc/jL9WHzWB/v6.gif
  9. Re: Hi i have question that i am sure the guru on here will know the answer to

    doubtful a v6 will operate a jet
  10. Replies
    11
    Views
    101

    Re: compression reading

    110-130 ish
  11. Re: Replaces Shift Cable Bellows, now stalls when not at Trailer Trim

    If the cable does not slide at all and you installed the clamp with the drive up the clamp is too tight, most use just a ty-wrap or you accidently glued the cable to the end of the bellow
  12. Re: Replaces Shift Cable Bellows, now stalls when not at Trailer Trim

    what type of clamp used on the bellows where the cable enters the bellow
  13. Replies
    1
    Views
    63

    Re: haunted 4.3 volvo penta?

    ign switch shorting out
    slave solenoid/relay shorting out
    starter solenoid shorting out
    battery cable at starter contacting the yellow/red wire on solenoid
  14. Replies
    1
    Views
    49

    Re: gimbal bearing

    just pulls out from the rear
  15. Re: Knock sensor location and mystery bolt location

    1 probable only have one knock sensor
    2 that is where the oil pressure sender for the gauge goes or if the sender is on the port side near the oil filter then plug the hole at the manifold/block...
  16. Replies
    2
    Views
    52

    Re: Shift Shaft Orientation

    if the control box is in full fwd its correct
  17. Replies
    1
    Views
    55

    Re: 1981 Larson tilt problem

    Stringers dont have trim/tilt sensors. full up or full down. If motor runs but no up travel inspect the clutch pack . Drive dosent care where it is....
  18. Replies
    9
    Views
    121

    Re: Distributer Cap and Rotor?

    retap for the next size , self tapping small screw or replace the dist body
  19. Replies
    2
    Views
    78

    Re: Wondering where this hooks up

    with the updated trim pump it goes nowhere, you should have the old style trim cylinders with the new type of trim pump. It was part of the reverse lockout system to lock the drive down in reverse...
  20. Re: 91 omc cobra 4.3 setting timeing after distributer gear replacement

    Yes ,you can install a dist and not worry about the timing and get the motor close and running but if your too advanced or too retarded you will damage the motor .
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4