Logo

Search:

Type: Posts; User: bondo

Page 1 of 4 1 2 3 4

Search: Search took 0.04 seconds; generated 49 minute(s) ago.

  1. Re: how to choose the correct prop. for optimum speed

    Ayuh,...... Only if you wanta burn holes in the piston tops,.....
  2. Replies
    3
    Views
    30

    Re: 19692T01 Pulley Removal

    Ayuh,..... Take the 4 bolts out, give it a few taps, 'n it oughta pretty much, fall off,......
  3. Thread: Leak issue help

    by bondo
    Replies
    1
    Views
    30

    Re: Leak issue help

    Ayuh,.... Tiltin' the drive shouldn't make any difference, at all,......

    My guess is the drive bellows is holed,....
  4. Re: mercruiser 5.0 had hole in oil pan fixed and refilled and now loud clanking and power loss HELP

    Ayuh,..... So what caused the hole,..??

    If ya ran it outa oil, I'm guessin' the bearings are junk, along with the crankshaft,......
  5. Re: Shift Intercept switch location on 1974 Mark Twain with 165 Mercruiser

    Ayuh,..... Look on the top of the transom inner plate, above the rear motor mounts,.....
  6. Replies
    4
    Views
    30

    Re: 1990 bass tracker tournament tx

    Ayuh,..... With resin, 'n cloth,..... Like boats are fiberglassed,.....
  7. Replies
    3
    Views
    60

    Re: 1979 seaswirl OMC 140 sterndrive

    Ayuh,..... There's only one way to find out,....... Ya gotta Look,.....
  8. Re: Could water ears flood a mercruiser v8 if engine not running ?

    Nope,..... Not if everything is in workin' order,.....
  9. Replies
    4
    Views
    30

    Re: 1990 bass tracker tournament tx

    Ayuh,.... Plywood is 4' wide, piece it together, 'n glass it into a single deck,.....
  10. Re: GM 5.7L , SB350ci DISTRIBUTOR CONVERSION INFO NEEDED

    Ayuh,..... The Delco Voyager is a reasonably priced, fine ignition swap too,....
  11. Replies
    2
    Views
    38

    Re: Blue Smoke After Season Startup

    Ayuh,..... Run it, 'n see if it uses any oil,......

    Check the spark plugs, 'n see if one is more fouled than the rest,.....

    Motors wear out,.... Could be rings, or valve guides,...
  12. Replies
    13
    Views
    130

    Re: RPM limits for operating -4.3 Alpha 1, Gen 1

    Ayuh,..... Yer motor doesn't have a rev-limiter,.... it's to old for that, rev-limiters are only seen on the newer Mpi/ Efi motors,...
  13. Replies
    6
    Views
    69

    Re: Replace Engine Coupler

    Ayuh,.... That proves Nothing,..... The hub can be blown, but still turn by hand,.....

    'n, Yes, the motor Has to come out to change the coupler,.....
  14. Re: Could water ears flood a mercruiser v8 if engine not running ?

    Ayuh,..... If you want any answers,..... Learn to use paragraphs,......

    No way in f*^kin' 'ell, I'm gonna wade through that word soup,......
  15. Replies
    5
    Views
    68

    Re: Metal behind prop shaft seal

    Ayuh,..... Exactly,....
  16. Replies
    11
    Views
    122

    Re: compression reading

    Ayuh,..... 150ish psi is a brand new motor,....
  17. Re: Hi i have question that i am sure the guru on here will know the answer to

    Ayuh,..... The hull, 'n transoms are very, Very different 'tween a Jet, 'n an I/O,.....

    'n the motors are generally set up quite differently,......
  18. Re: replacing waterpump impella and its v belt problems.

    Ayuh,...... You must use the proper puller,.....
  19. Thread: HELP a NUBIE

    by bondo
    Replies
    7
    Views
    123

    Re: HELP a NUBIE

    Ayuh,..... That's right, the raw water pump is on the top of the lower unit, 'n that hose is from the raw water pump,.....
  20. Replies
    1
    Views
    87

    Re: Aluminum hull care

    Ayuh,...... It'll probably be just fine, as is,.....
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4