Logo

Search:

Type: Posts; User: faztbullet

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    24

    Re: 150 mercury block repair

    Use these...
    https://www.ezlok.com/ezlok-insert-316-6
  2. Thread: VRO pump

    by faztbullet
    Replies
    23
    Views
    317

    Re: VRO pump

    Yes....
  3. Thread: VRO pump

    by faztbullet
    Replies
    23
    Views
    317

    Re: VRO pump

    If your still getting oil alarm after purge... replace VRO/OMS pump as you cannot rebuild the oil side only the fuel/air motor side.
  4. Replies
    3
    Views
    60

    Re: 1995 mecury 90 hp

    Water is to thick at marina....:cool:
  5. Re: Need Serious Help from an Ignition Expert

    Disconnect the blk/yell from switchbox
  6. Re: Rev limiter stopping motor from accelerating at cold startup

    Sounds more like shift switch out of adjustment or sticking
  7. Replies
    4
    Views
    59

    Re: 1989 Mercury Black Max 175

    Sounds like you lost the low speed side of stator on a bank of cylinders,
  8. Re: Engine is stalling out after planing out.

    Either top of fuel bracket leaking, plastic fuel line on cowling cacked or VRO air motor is bad. The vapor seperator(VS) is filled when you pump bulb, the VRO pulls fuel from chamber and delivers it...
  9. Replies
    17
    Views
    168

    Re: 90Hp Mercury late 80's early 90 model

    3 or 6 cylinder?
  10. Replies
    17
    Views
    168

    Re: 90Hp Mercury late 80's early 90 model

    What size is boat???
  11. Replies
    9
    Views
    157

    Re: Johnson 175 accelerating issue

    #72...….
    http://www.marineengine.com/parts/johnson-evinrude-parts.php?year=1997&hp=150&model=E150GLEUE&manufacturer=Evinrude&section=Fuel+Bracket+%26amp%3B+Components
  12. Replies
    9
    Views
    157

    Re: Johnson 175 accelerating issue

    Need to test fuel presure out to carbs(manual).A leaking/warped top on bracket will cause problem also as VRO cannot pull fuel as fuel chamber is a vacuum(thus the vapor pump on top).
  13. Replies
    9
    Views
    157

    Re: Johnson 175 accelerating issue

    Also sign of weak VRO pump as fuel bracket not filling fast enough...more demand than supply.
  14. Replies
    5
    Views
    100

    Re: Mercury 60HP Exhaust Manifold Gasket

    If they are the green/blackish gaskets no sealer as impregnated gasket..if grey paper use avation gasket sealer(NAPA)
  15. Re: 150 Johnson (2001) Carb - Starts, runs, engine is hot turn off, will not idle on restart

    If it has the aluminum anti siphon valve replace it with BRP valve as the aluminum ones cause problems. Only use a OEM bulb also.

    BRP anti siphon valve numbers:
    173273 for the 5/16
    173274 for...
  16. Replies
    10
    Views
    161

    Re: 1990 Evinrude 150 max adavance

    Set static at 24
  17. Re: Johnson 175 mystery running problem. (retired omc tech even puzzled)

    A broken crankcase seal ring with cause cylinders to crosstalk …..
  18. Re: 1981 Mercury 115HP 6 cylinder will start and run only on start circuit

    Its a assy and the rotor is molded on( non removeable)
  19. Replies
    10
    Views
    161

    Re: 1990 Evinrude 150 max adavance

    19-20 is for a 60 motor...whats your model number???
  20. Replies
    39
    Views
    381

    Re: 93 Evinrude 200 Wont Rev Past 3000 RPMS

    OSI system on on the 60 motors.....
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4