Logo

Search:

Type: Posts; User: racerone

Page 1 of 4 1 2 3 4

Search: Search took 0.14 seconds.

  1. Replies
    3
    Views
    23

    Re: 90hp johnson j90tlaem

    Those numbers are not encouraging.------Maybe inspect float valve on bottom carburetor.
  2. Replies
    4
    Views
    62

    Re: Starting Issue - '68 Merc 350S

    I think there are a total of 4 nuts to be removed.----Also keep track of any washers ( shims) when the top cowl lifts up and off.----Might have to deal with choke solenoid wire as well.
  3. Replies
    3
    Views
    23

    Re: 90hp johnson j90tlaem

    First thing I would do on one of those is a compression test -----Post the numbers here.
  4. Thread: Johnson 100GT

    by racerone
    Replies
    1
    Views
    10

    Re: Johnson 100GT

    The first thing to do is a compression test.-----Post your numbers.------No point spending any time or beer tokens without a compression test.
  5. Re: Compatible lower unit for 1977 johnson 70hp

    Absolute ZERO chance it will bolt on !!----Splines on top of driveshaft are totally different !!----Other differences as well.
  6. Re: Compatible lower unit for 1977 johnson 70hp

    There is ZERO chance that an 85 HP 4 cylinder lower unit fits !!!-----Just can not be done.
  7. Replies
    1
    Views
    12

    Re: 1987 Evinrude 115 Constant Alarm

    The tell tale indicates that the water pump is working.---However the tell tale water does NOT circulate through the block!!------I strongly suggest there is a blockage in water jackets.-----Research...
  8. Re: 1993 Johnson 115hp shift rod length setting

    Stop-----Review the correct way to measure shift rod height !!----Or hurry to your local boat shop to save you some aggravation and beer tokens.
  9. Replies
    1
    Views
    21

    Re: Oil assistance for a dummy

    A " direct injected " motor will not run for very long with oil mixed in the gas !!----They do not operate like a conventional 2 stroke.----If oil tank was empty you should do a compression test and...
  10. Re: 1993 Johnson 115hp shift rod length setting

    Set at 21-27/32"-----Was it in neutral when you measured / set it / guessed at this important measurement ?
  11. Re: Gear case cracked - 1960 Evinrude 40 HP 35520

    Might just be the cavity drain that was plugged , water froze and cracked it.----Very common.----Pressure test the gearcase.
  12. Re: 1993 Johnson 115hp shift rod length setting

    What length did you set it to ?
  13. Re: 1988 mercury 90hp no spark on 2 cylinders.

    Charge battery and inspect starter.
  14. Replies
    5
    Views
    44

    Re: 1960 Evinrude 40 HP 35520

    People take thermostats out because they do not know much about outboards !-----Step #1 is to remove flywheel ( 3 bolt puller ) and inspect coils.----Install new water pump impeller before your next...
  15. Re: 2005 90hp Johnson 2 stroke shakes very bad

    There is no EMM on this motor !!!!
  16. Re: 2005 90hp Johnson 2 stroke shakes very bad

    Trust your friend and replace the stator I guess.
  17. Re: 2005 90hp Johnson 2 stroke shakes very bad

    How did it run for you last season ?--------Check the gear oil.-----Check for bent propshaft.-----Bent propeller ?-----Hard to diagnose without good facts.
  18. Re: 1996 Mercury 2 stroke/ 4 cyl C40ELPTO - Thermostat Location

    What is the serial # of your motor ?----And have you looked at a parts diagram for that serial #-----This should be easy for you to figure ot !!
  19. Re: 1996 Mercury 2 stroke/ 4 cyl C40ELPTO - Thermostat Location

    They have made those 4 cylinder motors since 1954 or so.----I have one of those.-----I do not believe these motors ever had a thermostat installed !!
  20. Re: 1977 Mercury 85HP Engine Harness Confusion

    Missing wire may have been for an overheat warning.----Not all Mercury motors had that feature.-----But it was built into the wiring harness I believe.
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4