Logo

Search:

Type: Posts; User: bondo

Page 1 of 4 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    2
    Views
    49

    Re: surge break issue

    Ayuh,...... Change the whole coupler/ master-cylinder assembly,.....
  2. Thread: My 77 898 searay

    by bondo
    Replies
    1
    Views
    38

    Re: My 77 898 searay

    Ayuh,...... Is there a question here somewhere,..??..??
  3. Replies
    2
    Views
    100

    Re: replacing stern seal

    Ayuh,...... Welcome Aboard,...... You bought a money pit, that most parts can't be bought for,......

    Sell it, 'n if you want a sterndrive, buy yerself a Mercruiser, or Volvo,.....

    That...
  4. Replies
    9
    Views
    129

    Re: AQ225D with Pertronix HEI Dpark plug gap

    Ayuh,....... If yer motor is pre-'96, the right plugs are MR43T, gapped at .035",......

    If yer motor is '96 or newer, it's got Vortec heads, which use the longer MR43LTS plugs at .035",.....
    ...
  5. Re: 1987 Chris Craft model 196 Limited fuel tank issues

    Ayuh,..... Welcome Aboard,..... Don't know that particular boat, but the sequence is the same,.......

    Locate the tank, if there's a deck hatch big enough to pull the tank, yer in luck, as...
  6. Replies
    3
    Views
    241

    Re: Clicking metallic noise in exhaust

    Ayuh,..... This, ^^^, makes sense,....
  7. Re: Replace Metal Reservoir Trim Pump with Later Model Plastic Reservoir Style Pump?

    Ayuh,..... The lines are different,......

    The ole MC-1s use plastic return lines, the newer use crimped hyd lines,.....
  8. Re: Replace Metal Reservoir Trim Pump with Later Model Plastic Reservoir Style Pump?

    Ayuh,...... I did that,.......

    Remove all of the return line stuff, ei: reverse-lock, trim sender, etc, then install the new pump, with new trim lines,.....

    The pump end of the lines...
  9. Re: Prop for 5.7l omc cobra with king cobra outdrive.

    Ayuh,..... Higher,......

    Might wanta check the tach's accuracy too,.....
  10. Re: Prop for 5.7l omc cobra with king cobra outdrive.

    Ayuh,..... Look under the prop nut,.....
  11. Re: Prop for 5.7l omc cobra with king cobra outdrive.

    Ayuh,..... Take it off, 'n look closer,...... Props are stamped, or the pitch is cast, into 'em,......

    Many times, right under the prop nut,......

    When ya find the pitch, go up 4",.....
  12. Re: AQ225D power steering oil cooler, 1985 Sportcraft Fisherman

    Ayuh,...... It'll do that every time it freezes, unless you drain it,......
  13. Thread: 4.3 mercruiser

    by bondo
    Replies
    1
    Views
    313

    Re: 4.3 mercruiser

    Ayuh,..... Hi Tyler,..... Donno why you didn't post this in the Mercuiser forum, rather than Marine Power, a different manufacturer,.....

    The 4.3l went through quite a few changes over the...
  14. Re: Complete impeller and bellow kit for my Mercruiser 1.7 alpha one gen two

    Ayuh,..... The impeller, 'n bellows are Drive parts,......

    Which motor, don't matter,.....

    An Alpha 1, Gen.II is what you need to go by,....
  15. Thread: Water top #4. ?

    by bondo
    Replies
    11
    Views
    352

    Re: Water top #4. ?

    Ayuh,..... Do an air pressure test on the coolin' passages, insteada the cylinder,....
  16. Replies
    4
    Views
    452

    Re: Marine carpet corner trim?

    Ayuh,...... 1" aluminum angle comes to mind,.....

    Should be available at better metal supply shops,......
  17. Re: 1984 sportcraft with omc 350 stern drive trim problem

    Ayuh,...... Welcome Aboard,..... Bein' an '84, ya got an ole 800 Stringer drive, 'n that's why it was cheap,.....

    That's the Tilt yer workin' on, not trim,......
    It has to be run at full...
  18. Replies
    11
    Views
    512

    Re: Do carbureted engines have a steady idle?

    Ayuh,..... My carbed motors have always idle smoothly,...... do alotta that freshwater trollin',......
  19. Thread: Rebuild question

    by bondo
    Replies
    11
    Views
    529

    Re: Rebuild question

    Ayuh,........ Try here,.....

    A used motor in a rotten boat might be a cheaper option,..... a donor boat,... scrap, or trash what's left,....
  20. Thread: Rebuild question

    by bondo
    Replies
    11
    Views
    529

    Re: Rebuild question

    Ayuh,...... I think yer gonna have a tough time findin' anybody to put it back together, without some machine work, 'n matchin' new parts,.....

    A shop has to stand behind their work,....
    That's...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4