Logo

Search:

Type: Posts; User: zommer

Search: Search took 0.00 seconds.

  1. 1973 25hp evinrude 2 stoke outboard motor will not shift into forward gear

    Hello everyone.
    I changed the seals out in the gearcase and put it back together.
    I was very careful putting the gears back together and thought it was
    correct.When i pushed the shift rod it...
  2. 1973 25hp evinrude 2 stoke outboard motor/impeller housing spacer o'rings

    I am replacing the impeller and impeller housing.
    My question is. Do I need change the o-rings on the impeller housing spacer also.
    And what is the purpose of o-rings?
  3. Re: 1973 25hp evinrude 2 stoke outboard motor gearcase seals

    Ok.. Thanks...
  4. Re: 1973 25hp evinrude 2 stoke outboard motor gearcase seals

    I dont think u read my question close enough.
    I accidently pumped 25 lbs. of air into the gearcase and it blew air out the seal around
    the propeller shaft and blew the driveshaft out of the...
  5. Re: 1973 25hp evinrude 2 stoke outboard motor gearcase seals

    Well. I just got around to putting the gearcase back together.
    And I decided to do the pressure test.
    I pumped 15 lbs. into the gearcase and it held with no leaks I could find.
    But the book says...
  6. Re: 1973 25hp evinrude 2 stoke outboard motor gearcase seals

    Thanks
  7. Re: 1973 25hp evinrude 2 stoke outboard motor gearcase seals

    Hello again fd.
    Could u please tell me if I can use pennzoil marine hight-viscoity lower unit gear
    Lubricant 80w-90 in the'73 25 hp gearcase ?
    I can get it easy at wally world but cant find...
  8. Re: 1973 25hp evinrude 2 stoke outboard motor gearcase seals

    Thanks for the information.
    Im going attempt put it back together.
  9. Re: 1973 25hp evinrude 2 stoke outboard motor gearcase seals

    Ok fd. Thanks for all the information.
    Im going try to put it all back together.
    Charles
  10. Re: 1973 25hp evinrude 2 stoke outboard motor gearcase seals

    I certainly did not mean to insult u fdr.
    I have gotten different answers from different people
    and trying to learn what I should be using and doing as I replace the seals.
    This is my first time...
  11. Re: 1973 25hp evinrude 2 stoke outboard motor gearcase seals

    Thanks fot the bit.I was going to use the 847 to go under the impeller plate.
  12. Re: 1973 25hp evinrude 2 stoke outboard motor gearcase seals

    Thanks vics. Should I put a thin coat under the housing also as kimcrwb1 suggest ?
  13. Re: 1973 25hp evinrude 2 stoke outboard motor gearcase seals

    Thanks for the reply.
    I didnt see any sealant when I opened the water pump up.
    But this guy said I only needed it on the gearcase side and I saw none
    there either.
    My repair manual does say that...
  14. 1973 25hp evinrude 2 stoke outboard motor gearcase seals

    Hello , I am putting new seals in the gearcase and replacing
    the impeller and impeller housing in my '73 evinrude.
    In another forum a guy said to use omc/brp gasket sealant for the
    outside...
Results 1 to 14 of 14