Logo

Search:

Type: Posts; User: makomark

Page 1 of 4 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    1
    Views
    25

    Re: 1974 Glassmaster 18' tri hull

    Personally, I'd look for another boat....here on the east coast, there is no shortage of used trailer-sized boats for relatively cheap prices....

    You can make glass stringers but it won't be...
  2. Replies
    6
    Views
    89

    Re: New Crusader 7.4L?

    I haven't looked in a while - that said last time I looked you could get the reconditioned (factory) 6BTA's for ~$21K, with a gear and the install package. you may find the QSB's for a few more $K...
  3. Replies
    6
    Views
    89

    Re: New Crusader 7.4L?

    hard to find anything on it and what I could find is all PCM material, not Crusader...not a big deal as same corporate ownership though different target markets.

    What I did find said 452CID, not...
  4. Replies
    6
    Views
    89

    Re: New Crusader 7.4L?

    Crusader hasn't had a new production 7.4L for sale for a while....the only exception may be a dealer that has old stock.....PCM usually doesn't complete with itself

    They did offer a 'high output...
  5. Replies
    19
    Views
    353

    Re: Crank mounted raw water pump wobble

    I think that will work....the arm may have been bent - not much but you can see what a non-neutral force does....

    On the bolts, I did a little math and the 10.9 bolts are more like a grade 8. I...
  6. Replies
    6
    Views
    164

    Re: Pulley bearing noise, which one?

    i think you did well on that one...good luck!!
  7. Replies
    2
    Views
    51

    Re: Engine won't start

    If it was just idling, I'd doubt it overheated....

    without knowing any more history, I'd say you need to ensure the fuel is being delivered first....
  8. Replies
    2
    Views
    80

    Re: HELP... Crusader Serial# lookup......

    The serial numbers won't tell you which model you have unless you have access to the old Thermo-Electron records...

    In addition to what Rick provided above, the decals on the valve covers can...
  9. Replies
    58
    Views
    19,989

    Re: Old Crusader O&M Manual

    Reply sent - waiting on your side...:)
  10. Replies
    4
    Views
    98

    Re: Compression lock 15hp 4 stroke

    so it spins over fine with the plugs removed but you can't spin it over when the plugs are re-installed?

    If so, I'd check to make sure the correct plugs were used...
  11. Replies
    13
    Views
    304

    Re: Carby flooding

    2X !!!
  12. Replies
    19
    Views
    353

    Re: Crank mounted raw water pump wobble

    I wouldn't be real happy with that and agree with your concern.....

    So, regarding the root cause, the only thing I see remaining is the balancer itself (assuming you eliminate interference with...
  13. Replies
    19
    Views
    353

    Re: Crank mounted raw water pump wobble

    i watched & listened and thanks for the correction in the post.....

    I guess the first question is what are you using for a reference to determine that the pump is wobbling?

    The next is did you...
  14. Replies
    4
    Views
    136

    Re: Marine carpet corner trim?

    I think any flexible plastic will wear out in short order....if you want something more durable, TACO makes some UV stable edge moldings that may work. a heat gun may help with the contours...won't...
  15. Replies
    6
    Views
    164

    Re: Pulley bearing noise, which one?

    you can remove the belt to isolate the raw water pump from the circulating pump and alternator....regarding separating the source from the circulating pump or the alternator, when you remove their...
  16. Re: Carburetor leaking onto top of manifold after shutdown

    There is really no leak path "out the bottom of the carb" except for the throttle shafts....and they aren't wet in normal operation.....

    My guess is the fuel pump diaphragm has failed and the...
  17. Replies
    6
    Views
    145

    Re: Smartcraft gauges and Fuel Sender

    Sounds to me like your current sender follows the 'European standard'...the few smartcraft installations I've upgraded have all used the 'American standard' piece parts....
  18. Replies
    19
    Views
    353

    Re: Crank mounted raw water pump wobble

    I think you plan to use the dial indicator is a good start. pretty sure you are correct about the lack of indexing. I thought the pump mounted to the PULLEY flange vs directly against the damper?
    ...
  19. Replies
    1
    Views
    207

    Re: Identify engine

    I'd guess Kubota D950.....
  20. Replies
    4
    Views
    210

    Re: Paragon reverse transmission issue

    Its a valid model number....best bet is to check here:
    http://www.kalamazoomarinegear.com/transmissions/paragon/

    I haven't used them recently; last time I used them they were quite helpful....
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4