Logo

Search:

Type: Posts; User: RicardoMarine

Page 1 of 4 1 2 3 4

Search: Search took 0.09 seconds.

  1. Re: Chris Craft lancer 350 Q starter problems

    I'll ask again........ have you found a HTGR/PMGR starter motor for a REV RH Rotation SBC?
  2. Replies
    3
    Views
    35

    Re: 318 Edelbrocks and fuel guzzling

    Ditto Mark's comment.


    Look up your OEM ignition advance curve, and then make sure that each ignition system is delivering that curve.

    I'm referring to the Progressive advance and the Total...
  3. Replies
    8
    Views
    78

    Re: Volvo Penta AQ120 overheating

    As you’ve just learned, its tough to check for a suction leak with pressure.
  4. Replies
    4
    Views
    43

    Re: volvo penta aq131d engine removal

    If for some reason you do end up removing the drive, pull the transmission ONLY at first.
    Then if you need to remove further components, do so after the transmission has been removed.

    When...
  5. Replies
    4
    Views
    43

    Re: volvo penta aq131d engine removal

    In the Marine world, what you're calling a bell housing is actually a flywheel cover..... aka F/C.

    Inside of the flywheel cover will be a Borg Warner drive coupler, a PDS (primary drive shaft)...
  6. Re: Chris Craft lancer 350 Q starter problems

    Have you found a HTGR/PMGR starter motor for a REV RH Rotation SBC?
  7. Re: Volvo DP Cotrim Outdrive stock on Neutral.

    ........




    By the way, you will need an old spline coupler in order to make the tool for supporting the transmission while you disassemble it.

    The coupler will be welded to a short piece...
  8. Re: Chris Craft lancer 350 Q starter problems

    .......
  9. Replies
    3
    Views
    71

    Re: Replacing Starter

    My suggestions:

    Warm engine before attempting to crack the bolts loose.
    Once you have good access, use a SIX point wrench ONLY, and then crack the bolts loose.
  10. Replies
    12
    Views
    151

    Re: Volvo Penta fuel issue

    Carburetors want to see around 4 to 7 psi.
  11. Re: Volvo DP Cotrim Outdrive stock on Neutral.

    ...........

    We never remove an entire AQ series drive as a complete assembly.
    We remove the transmission first, then the other components if necessary.

    For what you are doing, you will...
  12. Re: Need help disassembling trim cylinder

    Yes, Bill and I go back many years regarding Volvo Penta.
    I tried calling him earlier this morning... no answer.

    I would contact him and see if he can help you when the parts come in.
  13. Re: Need help disassembling trim cylinder

    Ryan, it would be helpful if you were to post the year and model of your engine and stern drive.

    There is a man in Canada who may have the rebuild kits for these.

    Keep an eye on E-Bay sales if...
  14. Re: Volvo DP Cotrim Outdrive stock on Neutral.

    .....


    https://www.baylinerownersclub.org/filedata/fetch?id=528423&d=1565176314
  15. Replies
    8
    Views
    78

    Re: Volvo Penta AQ120 overheating

    Bart, the engine can be operated while the drive is partially up...... just don't rev it high.
    As for propelling forward with the drive up a bit.....yes, you can do it, but again, very gently. ...
  16. Re: Chris Craft lancer 350 Q starter problems

    Here is an example of what Chris Craft did for a flywheel facing forward installation.
    This one is apparently for a straight shaft drive.
    The reason for the flywheel facing forward was to lower...
  17. Replies
    8
    Views
    78

    Re: Volvo Penta AQ120 overheating

    ..........



    Bob makes some excellent suggestions here.

    The water neck fittings are wear items, and require routine replacement.
    There is a special beaded gasket underneath the water neck...
  18. Re: Chris Craft lancer 350 Q starter problems

    Bob brings up some interesting points.

    Which drive system?
    Is the engine mounted with flywheel facing forward, or is it a conventional installation?


    If Volvo Penta stern drive (even if...
  19. Replies
    4
    Views
    70

    Re: Asking price for a 3.7 488 185 HP

    I agree with hystat.

    These were Merc's own designed engine using the Ford 460 cylinder head.
    The rather large displacement allowed these to produce good torque.
    In my opinion, the intake...
  20. Re: Chris Craft lancer 350 Q starter problems

    While looking for a Marine SBC Reverse RH Rotation engine starter motor, I stumbled onto this old MarineEngine dot com thread.
    (the OP turned grouchy when he did not receive the answer he was...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4