Logo

Search:

Type: Posts; User: Deanmck

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    2,436

    1GM10 / 2GM handcrank handle

    Hi all.

    I am hoping one of you kind people could take the measurements of the manual crankhandle to the GM series motor. I need the internal & external diameter of the round turning tube plus it's...
  2. Replies
    13
    Views
    4,303

    Re: 1GM10 Black sludge not moving boat.

    A very late update.
    The throttle linkage was set wrong.
    Very esy fix.

    Thanks for all the help.

    Dean.
  3. Replies
    18
    Views
    4,458

    Re: BF50 Trim Angle Sensor - Bypass?

    Ps.
    Ive only ever seen them as complete units.
    you would need the arm, spring & screw to repair yours.
  4. Replies
    18
    Views
    4,458

    Re: BF50 Trim Angle Sensor - Bypass?

    I never replaced mine due to the crazy price.
    I don’t know where you are but e bay or boats.net are a good start.
    You can go on boats, get the part number, google it & see what pops up.
    I never...
  5. Replies
    18
    Views
    4,458

    Re: BF50 Trim Angle Sensor - Bypass?

    Hey Jim.
    if you look at your motor on the port side. The sender unit is on the inside of the transom bracket, tucked inside close to the tilt ram. There will be wires from the motor cowling leading...
  6. Replies
    13
    Views
    4,303

    Re: 1GM10 Black sludge not moving boat.

    I will check it out.
    Thanks.

    Dean
  7. Replies
    13
    Views
    4,303

    Re: 1GM10 Black sludge not moving boat.

    Ok
    I didn’t know that. Is there a online procedure or something I can read/ watch before I dive in?
    Thanks for the heads up.

    Dean.
  8. Replies
    13
    Views
    4,303

    Re: 1GM10 Black sludge not moving boat.

    No mate. I havnt checked the stuffing box, but she is up on a cradle for the winter now. The shaft spins freely out of gear if that’s what your referring too.
    Is there something you think I should...
  9. Replies
    13
    Views
    4,303

    Re: 1GM10 Black sludge not moving boat.

    Update.
    I have had the exhaust manifold off. There is no build up what so ever. I have also noticed that the throttle linkage was set somewhat wrong and was, I don’t think receiving full travel. I...
  10. Replies
    13
    Views
    4,303

    Re: 1GM10 Black sludge not moving boat.

    Cheers Ali.
    I really hope your right mate but I do suspect there is more to my problem. More or less. I just don’t know.
    Good luck on the snapper I’m jellous as mate.

    cheers
    Deano.
  11. Replies
    13
    Views
    4,303

    Re: 1GM10 Black sludge not moving boat.

    Thanks Doc.
    I have both the service manual as well as the 460 odd page workshop manual.
    I'm not short of documents, just advice on where to start.
    Thanks anyway mate.
  12. Replies
    13
    Views
    4,303

    1GM10 Black sludge not moving boat.

    Hi.
    I am new here.
    I have been on the Honda outboard forum for a number of years, but am now the proud owner of a sail boat and in need of assistance.

    A bit of background.
    I am a Kiwi living in...
  13. Re: Yanmar 1GM10 Exhaust Water very dark and peak 2400 rpms

    I have the same problem, more or less.
    I hope its an easy fix as my motor is newly reconditioned.
    Will start a new thread to see if anyone can help.
  14. Re: Oil discharge from Carbs PLUS Vacuum Pressure HELP - Honda BF40

    Yep Stu is a top notch bloke. His boating vids are the best.
  15. Re: Oil discharge from Carbs PLUS Vacuum Pressure HELP - Honda BF40

    If you decide to adjust the rockers. just a word of warning that it must be done correctly, especially on the exhaust valves. If you leave them too tight you can risk burning the valves creating a...
  16. Replies
    8
    Views
    851

    Re: Honda BF75 and avoiding carb problems

    I drain my carbs every time I'm sitting up for more than a few days. As long as you can still remove the engine cover it's dead easy. The fuel these days does not have the preservation additives it...
  17. Replies
    3
    Views
    1,232

    Re: Touch-up paint color

    You should be Auqamarine silver metalic. Paint number NHB14M. I think colour rite makes a spray, they may make pens.
    That is the paint for outboards after 2012
    Pre 2012 is Oyster Grey metalic...
  18. Replies
    5
    Views
    320

    Re: BF15 clamp screw pitch

    I live in Denmark and still use boats.net.
    after paying the import duties they still have a wider range of spares than I can find in Europe and work out cheaper in the long run.
    Shipping does take...
  19. Replies
    8
    Views
    741

    Re: BF2A 2HP misfiring any ideas?

    Try a new spark plug. NGK of course. I have the same wee motor as a kicker. As much as I neglect her she runs like a race horse. It may be more than that but start there and post your findings.
    ...
  20. Replies
    9
    Views
    3,934

    Re: Removing Honda Tilt Piston/Trim Component

    Good job ��
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4