Logo

Search:

Type: Posts; User: bcclew

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: Vdrive

    by bcclew
    Replies
    1
    Views
    300

    Re: Vdrive

    Anybody know the size of the flange nut. Is it 1&7/16? Thanks
  2. Thread: Vdrive

    by bcclew
    Replies
    1
    Views
    300

    Vdrive

    1976 silverten borg warner velvet trans and v drive its all one unit. Has ony one change the prop shaft flange seal.l think i canget the sfaft back enough to get at that big nut.any helpwould be...
  3. Replies
    1
    Views
    312

    Re: Seakamp ,4"" end cap

    36 to 72 inch lbs
  4. Replies
    1
    Views
    312

    Seakamp ,4"" end cap

    Anyone know the torque spec thanks
  5. Thread: Cables

    by bcclew
    Replies
    4
    Views
    155

    Re: Cables

    ok thanks
  6. Thread: Cables

    by bcclew
    Replies
    4
    Views
    155

    Cables

    1976 28 ft silverton with 2 crusaders 5.0 replacing shift cables 2 do the universal cables work ? J am changing ables from down stair helm these are factory controls not sure about cables has...
  7. Thread: bottom paint

    by bcclew
    Replies
    0
    Views
    148

    bottom paint

    any body around Barnegat bay had power washed for winter they always do a good job.this time it looks like a leopard spots.checked a few other boats at marina the have them too.their smooth from the...
  8. Replies
    1
    Views
    428

    1974 318 distributor

    is any body using the complete after market kit .with every thing new just hook up 2or 3 wires and set base timing. i have used the gm ones they work great.or trouble check this system? thanks
  9. Thread: float switch

    by bcclew
    Replies
    2
    Views
    250

    Re: float switch

    ok ill try it thanks
  10. Thread: float switch

    by bcclew
    Replies
    2
    Views
    250

    float switch

    this maybe crazy i changed float switch with a rule same as i had before. i think with the old switch it would come on and pump out.as the float hit the bottom.it seemed to run for a few seconds.this...
  11. Thread: Trans type

    by bcclew
    Replies
    3
    Views
    135

    Re: Trans type

    Thanks
  12. Thread: Trans type

    by bcclew
    Replies
    3
    Views
    135

    Trans type

    1996 silverton 31ft 454 mercs v drives what trans is most popular?tanks
  13. Replies
    2
    Views
    214

    Re: No one cyl 2014 yamaha v8

    Thanks
  14. Replies
    2
    Views
    214

    No one cyl 2014 yamaha v8

    Faceing the bow of the boat standing behind the engine where is number one port or starbord top or bottom? I downloaded mznual gives cireing order but not positionof number 1 cylthanks
  15. Thread: shore power

    by bcclew
    Replies
    6
    Views
    1,679

    Re: shore power

    thanks gu7ys
  16. Thread: shore power

    by bcclew
    Replies
    6
    Views
    1,679

    shore power

    1976 26 ft silverton ac shore power .when plugged in in live state that i no should not be done but if done while plugging in i hear a buzzer? i looked under deck seems to be some type of box like a...
  17. Thread: soft spot

    by bcclew
    Replies
    5
    Views
    7,443

    Re: soft spot

    late reply followed video cut out section re did it all over. came out good.cost 400.00$material thanks for replys
  18. Thread: blowing fuses

    by bcclew
    Replies
    3
    Views
    391

    Re: blowing fuses

    Sorry to get back so late bt righr on. Gray wire to tbi was rubing hat on blows fuse hat off ran good. Fixed gray wire back in shape thanks for comebacksbcc lew
  19. Thread: blowing fuses

    by bcclew
    Replies
    3
    Views
    391

    blowing fuses

    mercruiser1998 5.7 tbi I had another post on having a bad fuel injector same engine. new prob engine run fine starting it and let it mabe 5 mins. or even 20 mins then blows ing. relay fuse15 amp and...
  20. Thread: Distributor

    by bcclew
    Replies
    6
    Views
    258

    Re: Distributor

    update 7/24/20 bought a gm est distributor kit from united marine engine parts. hardest part making a bracket for the coil.3 hour job not to bad runs fine thanks for all the input bcclew
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4