Logo

Search:

Type: Posts; User: Bt Doctur

Page 1 of 4 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    10
    Views
    40

    Re: Need help disassembling trim cylinder

    https://duckduckgo.com/?t=ffab&q=volvo+trim+cylinder+rebuild+kits&atb=v224-1&ia=images&iax=images&iai=https%3A%2F%2Fd1f7geppf3ca7.cloudfront.net%2Forigin%2F225846%2F1561162552717_caddrawingsxdps-mcyli...
  2. Replies
    10
    Views
    40

    Re: Need help disassembling trim cylinder

    https://d1f7geppf3ca7.cloudfront.net/origin/225846/1561162552717_caddrawingsxdps-mcylinder.png
  3. Replies
    10
    Views
    40

    Re: Need help disassembling trim cylinder

    https://i.ebayimg.com/images/i/132292095457-0-1/s-l1000.jpg
  4. Replies
    10
    Views
    40

    Re: Need help disassembling trim cylinder

    Most cylinders unscrew the cap from the rod end, Do you have a model type of the drive?
    click to enlarge
    https://i.postimg.cc/ppTYxnLH/external-content-duckduckgo-com.jpg
  5. Replies
    10
    Views
    40

    Re: Need help disassembling trim cylinder

    A human assembled it, look for a snap ring, lock ring, etc. Does anything unscrew from the other end
  6. Replies
    3
    Views
    67

    Re: Replacing Starter

    You may have to remove the exaust manifold for better access, drain it first
    cut/remove any side panels
    Option 2 is remove the motor, some boats need the motor removed to change it
  7. Re: 95 Mercruiser 350 Magnum Tournament Ski TBI fuel pump replacement

    any pump mounted to the engine block where a fuel pump goes will not work for a TBI. You need atleast 30-32 PSI for the 2 injectors
  8. Re: Is this 4,3 Gxi-M runnig as it should?

    From the sound of it I think its the bearing on the adjuster pully or the idler pully
    Från ljudet av det tror jag att det bär på inställningsskivan eller tomgångsskivan
  9. Replies
    2
    Views
    58

    Re: mercurise tbi stalling

    They should
  10. Replies
    6
    Views
    151

    Re: 1979 seaswirl OMC 140 sterndrive

    I was told it could be frost plug

    There is no such thing, there "core" plugs If the motor was not winterized correctly one was pushed out
  11. Replies
    6
    Views
    104

    Re: Replace Engine Coupler

    shift into gear, have someone watch the shaft behind the motor stand on a blade to see if it turns
    prop turns, shaft turns=coupler
    prop turns, shaft does not= internal drive damage
  12. Re: How to remover water pump idler pully withseized to bushing and pinion stud.

    If the pully is seized to the bushing and the bushing is seized to the bolt, just cut everything off and replace with new
  13. Replies
    12
    Views
    150

    Re: Volvo Penta fuel issue

    except the high pressure and low pressure look exactly alike
  14. Replies
    6
    Views
    91

    Re: 1985 3.8 removal

    #35 V8 is the same
    https://www.l-36.com/pdf/manuals9/omc_7.png
  15. Replies
    6
    Views
    91

    Re: 1985 3.8 removal

    If you can get to the bottom of the dust cover and remove the bell housing bolts AND IF THE COUPLER IS NOT RUSTED TO THE INPUT SHAFT motor pull forward and up /out
  16. Replies
    6
    Views
    91

    Re: 1985 3.8 removal

    https://www.l-36.com/pdf/manuals9/omc_13.png
  17. Replies
    2
    Views
    106

    Re: Raw water inlet hose

    best bet is a good auto parts store and make one up .Doubtful after 60 years there is one in stock anywhere
  18. Replies
    6
    Views
    91

    Re: 1985 3.8 removal

    Depends, if a stringer ,you can just remove the engine ,on a Cobra you need to remove the drive first
  19. Replies
    6
    Views
    111

    Re: AQ171c Plug wire placement

    If you mean the flat cap ,stand by
    https://i.postimg.cc/MnQndvVH/original.jpg

    https://i.postimg.cc/jL9WHzWB/v6.gif
  20. Re: Hi i have question that i am sure the guru on here will know the answer to

    doubtful a v6 will operate a jet
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4