Logo

Search:

Type: Posts; User: racerone

Page 1 of 4 1 2 3 4

Search: Search took 0.18 seconds.

  1. Re: 93 Mercury classic 40HP ran perfect and now dies intermittently and bogs down when does run

    Friend just bought a boat with a 40 HP just like that.------Tested in the water at the ramp before purchase.----Tested in the lake here at home.----Just installed a new water pump impeller as...
  2. Replies
    19
    Views
    114

    Re: 2000 Johnson 25hp 3cylinder

    Did your neighbor say / suggest it was a coil that was bad ?
  3. Re: Outboard Mounting Bolts/Nuts - Stainless and Bronze?

    Part prices for modern machinery includes huge factory , warehouse overhead and shipping costs.----But it will be the correct nut and bolt.------So yes----You can visit the local nut / bolt supply...
  4. Re: Installing External Fuel Filter - How Critical is Placement in Direct Sun?

    Just install it.----Hang a wee curtain in front of it should the dreaded vapour lock occur.
  5. Re: Dumb question re sierra push in primer key start switch

    The fuel primer is not a pump.-----It is a valve that opens when key is pushed in when ----ON and DURING cranking.-----The fuel primer valve does nothing if there is no fuel pressure to...
  6. Re: 35hp merc. Canít get it to shift after removing the lower unit

    A very common event after water pump work.-----Hopefully you did no damage during your work.----You are aware that the prop must be turned when shifting from neutral to reverse.
  7. Re: 35hp merc. Canít get it to shift after removing the lower unit

    Did you remove the lower unit with control in neutral ??-----If so that remove lower unit again.----Put cables back in place.----Put control in neutral.------Put lower unit in neutral and...
  8. Re: Screw perforation in underfloor gas tank. Advice and help

    Some plastics can be welded.----You must nave somebody in the GTA that you can consult.---Auto body shops may help find somebody.
  9. Re: 2002 Mercury 2 Stroke - Shift Link Replacement

    That part # looks like the correct one.------Remove the lower side cowling and replace the link.
  10. Re: 15hp block repair, Engine shop drilled right through cylinder head bolt holes

    Used blocks are easy to find.----If in Canada---evinrudeparts.ca ----May be of help.
  11. Replies
    6
    Views
    47

    Re: 1997 Evinrude 90 HP Rough/Low Idle

    Water coming out of the tell tale does NOT go through the engine.
  12. Re: Screw perforation in underfloor gas tank. Advice and help

    Your location in southern Ontario ?
  13. Re: 2002 Mercury 2 Stroke - Shift Link Replacement

    73402 looks different.-------Not likely the correct part.----Any more pictures of this motor ???
  14. Re: 15hp block repair, Engine shop drilled right through cylinder head bolt holes

    Many of these motors were built.----Many good used blocks are available.----E-bay is one place to look.
  15. Replies
    6
    Views
    45

    Re: 235 evinrude year

    Some will argue.----you have a bad battery , bad starter , bad gauge , or a motor that needs major repairs.
  16. Replies
    11
    Views
    80

    Re: 2006 4 stroke 9.9 merc oil in carb

    Is there an automatic compression release on the valves ??
  17. Replies
    11
    Views
    80

    Re: 2006 4 stroke 9.9 merc oil in carb

    Compression release on the valves ???
  18. Replies
    6
    Views
    45

    Re: 235 evinrude year

    Well---75 PSI compression is a big red flag in my opinion.
  19. Replies
    19
    Views
    114

    Re: 2000 Johnson 25hp 3cylinder

    Good luck with it.----Trust your neighbor.
  20. Replies
    8
    Views
    85

    Re: I Suspect???? a weak Battery??

    Most garages / battery retailers will load test a battery in just minutes.----Often a free service , at least my local shop does.------2 bolts takes the starter apart.----Need a digital ohmmeter to...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4