Logo

Search:

Type: Posts; User: Bt Doctur

Page 1 of 4 1 2 3 4

Search: Search took 0.03 seconds.

  1. Re: Mercury 3.0 Gimbrel bearing change but now itís in gear all the time

    Shift slide not correctly positioned
  2. Re: Mercruiser 3.0 only starting with starting fluid

    Keep using stater fluid and you will be replacing the pistons. FIX THE PROBLEM
    Will it start using about 2 oz of gas instead?
  3. Replies
    3
    Views
    143

    Re: mechanical fuel pump overflow line

    chain saw repair shop
  4. Re: New Altenator Putting Out 15.25 volts, Is That OK?

    I had a new altenator installed and it's putting out 15.25 volts
    I'm only getting 12.8 to the batteries

    So what is the correct one? 15.25 will cook the batteries but 12.8 means not charging
  5. Replies
    3
    Views
    121

    Re: 2010 3.0 TKS Oil in Bilge

    yes, gear oil from the inputshaft seal leaking into the bellow, thru the gimbal bearing into the bilge
  6. Replies
    7
    Views
    187

    Re: Electric Fuel Pumps

    30 bucks or so on the other bidding site
  7. Replies
    20
    Views
    677

    Re: Engine stalls shifting into forward

    getting rid of that shift assist will improve shift control greatly
  8. Replies
    7
    Views
    187

    Re: Electric Fuel Pumps

    no mechanical pump will cost 300. go with the 4-7 psi eaton pump
  9. Replies
    3
    Views
    99

    Re: 3.0L overheating

    yes, impeller in the drive
  10. Replies
    3
    Views
    99

    Re: 3.0L overheating

    2 things to check, does the hose from the circ pump to the T Stat get hard with the rpm?
    Yes, clogged,restricted riser.
    High speed overheats always start with the impeller, recheck your work....
  11. Replies
    3
    Views
    121

    Re: 2010 3.0 TKS Oil in Bilge

    only 3 to pick from. Engine, trim pump or outdrive
  12. Re: Does anyone know the part # or bolt size for this engine block bolt?

    It could be the location for the dipstick tube.
  13. Re: AQ131a with Solex carb (old style) just won't stay running unless at 2000 rom

    I have the Solex carbs from the inline 6
  14. Re: Mercruiser VesselView4 - Low Voltage Warning

    turn off charger and shore power, put a voltmeter on the battery, engine off, what does it read.
    Start the engine, what does it read. If you not reading atleast 13.6 your not charging and the...
  15. Re: 96 MCM 3.0LX Won't Start, Tried everything except ______ !? (Starts off Remote Switch)

    the relay clicking means your good from the key switch to the slave. Jump the 2 large lugs on the slave , starter works Yes =bad solenoid , No= No power on the Red/Purple wire.or broken wire from...
  16. Re: AQ131a with Solex carb (old style) just won't stay running unless at 2000 rom

    You disconnect the throttle cabel to make the adjustments
  17. Replies
    2
    Views
    249

    Re: 1980 searay 260 sterndrive issue. Slips

    spun coupler or no gears in the upper
  18. Replies
    9
    Views
    2,215

    Re: engine pulley- 807728 obsolete

    https://www.summitracing.com/search/part-type/power-steering-pulleys/make/chevrolet/power-steering-pulley-grooves/6-groove-serpentine
  19. Replies
    1
    Views
    257

    Re: Oil plug assembly 861150A1

    Are you trying to add it or replace the broken one
  20. Thread: oil pressure

    by Bt Doctur
    Replies
    2
    Views
    167

    Re: oil pressure

    verify with a oil pressure gauge installed
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4