Logo

Search:

Type: Posts; User: baddog1016

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Re: Johnson Evinrude Outboard Fault Codes

    I had a couple of them
  2. Replies
    2
    Views
    47

    Re: 2000 Evinrude 225 spark plug gap

    Thanks.
  3. Replies
    2
    Views
    47

    2000 Evinrude 225 spark plug gap

    Can someone tell me what the spark plug gap should be for a 2000 Evinrude 225 Ficht? Shop manual says consult emissions sticker but the sticker is gone off of this engine. Currently has Champion...
  4. Replies
    12
    Views
    305

    Re: 1998 115 ficht no spark

    I spoke to an EMM builder about my issues and he said I should send my EMM to him. He was kind of pushy about it and wasn't really offering any troubleshooting advice. I sent it to another rebuilder...
  5. Replies
    12
    Views
    305

    Re: 1998 115 ficht no spark

    I'm going through this with a 225 FICHT. The engine has to crank over 200 RPM to generate a crank position sensor signal. Problem is that you pretty much can't check this without spark. Make sure...
  6. Thread: PRV

    by baddog1016
    Replies
    9
    Views
    217

    Re: PRV

    No CPS signal, there was a check CPS synch error on the software as soon as I cranked the engine over. The problem is at the connection, CPS side. I can see where the pink wire has been flexed enough...
  7. Thread: PRV

    by baddog1016
    Replies
    9
    Views
    217

    Re: PRV

    Thanks, I'll be checking things shortly, including cranking RPM. my issues started trying to diagnose the low idle, which was causing stalling. My starter motor was probably abused some while doing...
  8. Thread: PRV

    by baddog1016
    Replies
    9
    Views
    217

    Re: PRV

    The fuel pump runs when I turn the key. I actually just reinstalled the EMM after sending it out because of a no crank issue (fixed by replacing a bad diode), a battery voltage low code but battery...
  9. Thread: PRV

    by baddog1016
    Replies
    9
    Views
    217

    Re: PRV

    Thanks guys, my Fluke 88 can do the peak voltage.
    The lights do there normal count down when the key is turned on. I do have the software but I haven't used it that much I plan on playing with that...
  10. Thread: PRV

    by baddog1016
    Replies
    9
    Views
    217

    PRV

    I'm trying to diagnose a no spark issue on a 2000 Evinrude 225 Ficht motor. The manual says to check coil voltage with a PRV but it does not give a list of acronyms anyplace in the manual. Does...
  11. Replies
    1
    Views
    92

    solder or butt connectors

    I've worked on cars for a long time and would always rather solder and heat shrink two wires together as opposed to using crimp connectors. I have to replace a diode in my outboards wiring harness....
  12. Replies
    3
    Views
    96

    Re: 95 Evinrude 130 shift rod height

    http://www.marineengine.com/boat-forum/blob:http://www.marineengine.com/d095f04c-4454-44f5-9642-303e25bb7847
    I would say yes.
  13. Replies
    11
    Views
    158

    Re: 2 power heads in 3 years

    It would be good to see some pictures. If it was an oil problem you would have scoring on pistons and cylinder walls and I don't think the wrist pin would be the first failure, ultimately the wrist...
  14. Re: spark plugs for 2000 225 Evinrude Ficht motor

    I had my champions out yesterday and they don't look bad. My biggest issue with them is that the lead thread always seems to be in the same two places making it tricky to index them.
  15. spark plugs for 2000 225 Evinrude Ficht motor

    I'm not mentioning any names but I was told by one of the guys who fixes EMMs that there is an NGK plug that works better than the Champions that Evinrude calls for. Her did not know the number off...
  16. Re: 2000 E115 Ficht - relay preventing start - please help!

    I spoke to Eric at Marine Computer Supply this morning, he told me that if my fuel pump runs for ten seconds when the key is first turned to start it's not my EMM causing the no crank condition. I...
  17. Re: What affects idle speed on Ficht engines?

    I replaced the EP, and battery voltage was at 12.4 volts. I just noticed 40V circuit was at 31 volts. I was talking to someone yesterday who told me that will affect idle speed as it affects injector...
  18. Re: What affects idle speed on Ficht engines?

    faztbullet, thanks! I was doing a cylinder drop test when two things happened:
    Code 26 was set and and I had a no crank issue that I am sure is the EMM. I am including screen shots of the data to...
  19. What affects idle speed on Ficht engines?

    Specifically a 2000 225. My engine idles too low (380-400 RPM) and I was under the impression this is controlled by the EMM. I was told today that is not the case that there has to be a different...
  20. Re: 2000 E115 Ficht - relay preventing start - please help!

    I tried my three legged relay jump and the engine did not start. I spoke to Harris at EMM Repair and he told me it is the EMM and that jumping the relay would not work. (he was right). He said 4 day...
Results 1 to 20 of 33
Page 1 of 2 1 2