Logo

Search:

Type: Posts; User: CHARLIE W

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    66

    Re: 86 Mercury 115 Shock!!

    Thanks Guys, To update, found dead #6 coil (cracked). Boat has separate Morse control with trim switch and start/ign key switch on dash.
    Just wondering if voltage from trigger is following the...
  2. Replies
    3
    Views
    66

    86 Mercury 115 Shock!!

    I have 1986 merc 115hp inline 6 0a975284. When throttle control is moved it will sometimes give you a shock that travels up your arm. This engine also lost power and idled home, then quit and...
  3. Replies
    3
    Views
    549

    Re: Ford sabre 280c seized

    Hi Boatman1 , In most cases you will have to tear it down completely and have it bored oversize. The piston rings i'm sure are stuck in the grooves and cylinders pitted. If you did manage to clean it...
  4. Replies
    3
    Views
    549

    Re: Ford sabre 280c seized

    Hi Boatman, My quess is that the intercooler has leaked into the intake and cylinders. Get a small bore scope on ebay or Harbor freight and check each cylinder for water or rust. If that is the case...
  5. Replies
    2
    Views
    769

    Re: 2712E vs 2701E

    Hi, First your 2701e is 242 cu.in. 2712e is 254 cu.in. The injectors can be swapped but you may lose power. The correct injector tip is bdll140s6622 Basically it would be best to rebuild the 2701e...
  6. Replies
    2
    Views
    1,180

    Re: Ford Sabre 2704 ET Spare Parts need

    Hi Spiros,
    Try American Diesel Corp Virginia USA 804 435 3107 The early engines had Chrome pressed in sleeves which later changed to cast iron with chrome rings.
    Charlie W
  7. Replies
    2
    Views
    1,636

    Re: Oil pressure gauges.

    The sender in the middle of the engine with two terminals is oil pressure. Behind the alternator with two terminals is alternator energizing switch and single terminal is oil alarm switch.
    Charlie W
  8. Replies
    2
    Views
    3,098

    Re: Advice needed

    Colly, Yes the engine block is identical, but the bolt on supports may be different dimensions so just swap them. Also the trans to flywheel housing are identical, but on some engines a 200#...
  9. Replies
    1
    Views
    3,626

    Re: Raw water pump drive

    Hi, Sorry to say this coupling is no longer available. However you may find the pump side coupling on ebay It was a browning CHFS2X5/8 A local machine shop can make you a nylon centerpiece. For the...
  10. Replies
    4
    Views
    2,958

    Re: Paragon transmission issue

    Joe, Transmission Marine 800-462-8848 ext.427 has parts for your trans.

    Charlie w.
  11. Replies
    4
    Views
    2,958

    Re: Paragon transmission issue

    Joe, I believe you have turned the lock ring in too far. Back it off two notches and try again.

    Charlie W
  12. Replies
    1
    Views
    3,050

    Re: Lehman 80hp water in sump

    Hi, Need more info. Why was head removed? Overheated? Is the oil pan off? How do you know water goes up and down? When pressurized can you turn it 4 or more times with out locking up?
    Charlie W
  13. Re: Leaking Rear Seal on Velvet Drive Transmission

    Hi Scott Free, no , it will come off fairly easy.

    Charlie w.
  14. Re: Leaking Rear Seal on Velvet Drive Transmission

    Hi Scott Free, Did you put #2 permatex or rtv on the splines and under the coupling nut?? If not it will leak. Also if the seal riding surface on the coupling is worn you should replace it....
  15. Re: Random RPM drop or engine stall after 2 hours

    Thanks for the info. doubtful that this is an injection pump problem. I have seen similar problems when fuel tank vent lines droop down over time and if the tanks are overfilled the vent lines fill...
  16. Re: Random RPM drop or engine stall after 2 hours

    Hi, Can you tell me the year of your engine ? In the meantime i would try running out of a five gallon container of clean fuel connected to the lift pump to see what happens.
    Charlie W
  17. Replies
    4
    Views
    4,389

    Re: Replacing VDO instruments on Lehman 135's

    Hi Jim, It would be best to change gauges and senders at the same time. Check with American diesel, they may still have some original VDO's or equivalent. 804-435-3107
    Charlie w.
  18. Re: Low oil pressure & dropping with higher rpms on Lehman 120 hp twins (?)

    Hi. The oil sample should tell you whats going on, but at 3000 hrs it's most likely cam and crank bearings. are you using a Fram PH8A oil filter or equiv.? If you do replace bearings, change oil...
  19. Replies
    5
    Views
    4,478

    Re: What Gray Marine Engine do I. Have?

    Hi,
    You have a 1950's 224 cu.in engine with zenith 63m2e12 spec10870 carb also used on lugger exp6-226 &luggerexp6-224.
    Charlie W
  20. Re: I am considering buying a boat that has a 1986 Lehman 135HP diesel engine that------

    George, assuming everything was checked ,the engine should be good for another 6000 hours. Have the head bolts torqued after 20 hours then normal maintenance.
    Charlie w'
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4