Logo

Search:

Type: Posts; User: RicardoMarine

Page 1 of 4 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    20
    Views
    203

    Re: Mercruiser over prop overheat?

    In post #1, you mention Bravo 3!
    I'm not seeing a B 3 4 blade set in a 15 pitch!
  2. Replies
    3
    Views
    118

    Re: 250 or 270 or 280

    You are welcome.


    Tip......
    When removing the transmission, and when you reach this point........
    ...
  3. Replies
    3
    Views
    118

    Re: 250 or 270 or 280

    .............
  4. Replies
    2
    Views
    83

    Re: 270 Heat Exchanger Advice

    I agree.... replace the rubber end plate gasket.
    Also look to see if the end plate has become "cupped". If cupped, you may want to replace it also.

    As for the pencil anode, I also agree that...
  5. Re: Aq engine removal and replacement advice needed

    Short answer....... no!

    The 105 is a push rod engine..... the 125 is an OHC engine.
    The rear flange for the flywheel cover is very different..... not to mention several other areas that would...
  6. Re: Please Help I.D. starter pre 78 stringer drive starter ?

    Ben, post a few good photos of your drive. It will help those who may know identify the drive.
  7. Re: Distributor gear worn in strange manner?

    ...........
  8. Re: 1989 Mercruiser 3.0L Retrofit EST Timing?

    If you do not chemically clean the balancer surface before applying the decal, yes!
  9. Replies
    33
    Views
    294

    Re: HELP MAYDAY TOTALY GREEN Scallywag !

    ..............
  10. Replies
    33
    Views
    294

    Re: HELP MAYDAY TOTALY GREEN Scallywag !

    It's not uncommon to see where some knuckle-head tossed a mismatched cylinder head onto an engine.


    Pull the valve covers and read the cylinder head casting numbers.
    They should both be the...
  11. Re: Distributor gear worn in strange manner?

    Great point.
    If the distributor housing's lower bushing is heavily worn on the one side, the two gears will want to separate, possibly causing the unusual wear pattern.
    As said, go in with a bore...
  12. Replies
    33
    Views
    294

    Re: HELP MAYDAY TOTALY GREEN Scallywag !

    The best we can offer you, would be to take some very good and clear images.
    Then start a new thread with a title like; "Please help me identify my OMC Stringer Drive" or similar.
    Post your...
  13. Re: Distributor gear worn in strange manner?

    That would be the distributor's "driven" gear. And yes, it is showing signs of an unusual wear pattern, as in perhaps excessive resistance.

    You will want to go in with a bore scope and look at...
  14. Replies
    33
    Views
    294

    Re: HELP MAYDAY TOTALY GREEN Scallywag !

    ..................
  15. Replies
    33
    Views
    294

    Re: HELP MAYDAY TOTALY GREEN Scallywag !

    Ben, I see two potential scenarios:


    1.... you absolutely love this boat because your dad or grandfather owned one when you were young.
    You are willing to do what ever required to breathe life...
  16. Replies
    4
    Views
    120

    Re: Log style riser gaskets

    By chance is this a block-off-plate, and not a gasket?
    Block-off-plates will be absent any seawater transfer ports.
    Gaskets will include the seawater transfer port openings.

    As Mark says, the...
  17. Re: 1989 Mercruiser 3.0L Retrofit EST Timing?

    Smart move! I agree.
  18. Re: 1989 Mercruiser 3.0L Retrofit EST Timing?

    ...................

    You are switching ignition systems only, and have not changed any internal engine components, correct?
    If so, your engine will be happy with the same ignition advance curve...
  19. Re: Volvo Penta Float Needle & Seat Cleaning

    Did you mean that these are 5.7 GXiE?
  20. Replies
    6
    Views
    132

    Re: DP 570 antifreeze in Bilge

    ....................
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4