Logo

Search:

Type: Posts; User: fitznooney

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    209

    Re: Oil pressure sender Marine 360

    Pretty sure that Chrysler used these on all their engines.
    Worked as a replacement on my MN6/33.
    https://www.stewartwarner.com/product/pressure-sender-pn-82501/
  2. Replies
    1
    Views
    586

    Re: Chrysler 655 N/A question

    They should be a Mitsubishi 6DS7 engines.
    They came in N/A and and turbo versions.
    The factory turbos were 200HP.
    They could also be after market upgrades of the N/A motor.
  3. Replies
    3
    Views
    374

    Re: Chrysler 300 Stern drive

    Take the top cover off and see what is causing the problem.
    Might only be a seized cable.
  4. Replies
    5
    Views
    542

    Re: Cylinder wall stain

    Get an itemised list of what was done during the overhaul.
    Then you can make a informed decision on the condition of the engine.
    Personally I wouldn't touch it.
  5. Replies
    1
    Views
    3,358

    Re: SD-33 marine engine, newbie questions

    It should not need a lift pump as the feed pump on the side of the IP can deliver more than max engine power requires. That's why there is a return line to the tank.
    Disconnect the return line with...
  6. Replies
    10
    Views
    5,946

    Re: CM6-55 Engines

    Hi Allan,
    LH props would be pretty rare in Australia.
    Seems odd that the input shafts are different.
    What powerplant are you running and in what hull?
    Mobile 0409370710.
    Cheers,
    Mike
  7. Replies
    10
    Views
    5,946

    Re: CM6-55 Engines

    Right hand.
  8. Replies
    10
    Views
    5,946

    Re: CM6-55 Engines

    About six years ago I got a quote of $25,000 AUD, landed in Australia.
    I would be looking for around $15,000 for it.
  9. Re: Water trickling from hydraulic pump for DANA outdrive

    Not sure what you mean. There should not be any water in a hydraulic pump.
    Can you take some pictures.
  10. Replies
    8
    Views
    7,944

    Re: Turbocharged CN4-33

    I think you might be a bit confused on how the turbo bearing is lubricated and cooled.
    They either it is oil lubricated and oil cooled or oil lubricated and water cooled.
    The water does not come in...
  11. Replies
    8
    Views
    7,944

    Re: Turbocharged CN4-33

    I have turboed and intercooled my SD33. Egts are dependent on how much fuel you add.
    If you have your boost set so you burn all the fuel before reaching max boost, the excess charge will bring your...
  12. Replies
    8
    Views
    7,944

    Re: Turbocharged CN4-33

    Is it a 4 or 6 cylinder engine?
  13. Replies
    3
    Views
    1,070

    Re: Still having belt issues

    Make sure the pulleys aren't worn.
    A new belt of the correct section should sit about 1/16" proud with the rim of the pulleys.
    If it sits deeper the pulleys need replacing.
  14. Replies
    1
    Views
    9,920

    Re: Nissan P40 Thermostat

    Are you sure it is a P40 engine and not a SD33.
    The P40 is a petrol engine used in the Patrol and as far as I know it was never used by Chrysler Marine.
  15. Re: Newbie question: Are any differences between Chrysler Nissan Diesel SD33 and Patrol 160 series S

    It is not a manual. It is a sales brochure.
    The M6-33 is based on the SD33. It was also known as a CN6-33.
    As per the brochure the rated power is 105HP @ 4000rpm.
    With the right prop, WOT should...
  16. Replies
    1
    Views
    12,797

    Re: Looking for workshop manual

    Same basic motor as a MQ Nissan Patrol. Manuals are available online.
  17. Re: Newbie with boat I maybe shouldn't have bought

    You will have to wait a long time for it to die, if it is in good condition.
    I have over 1,000 hours on mine and it is still going strong.
    What part of the world are you in?
    You should have no...
  18. Re: Newbie with boat I maybe shouldn't have bought

    Give us a pic of the leg, so that we can identify it.
  19. Replies
    2
    Views
    9,075

    Re: Need help: Chrysler Nissan M8V75

    Sounds like you have a UD Nissan V8. A Jap copy of the GM diesel.
    Chryler as far as I know nver used this engine.
  20. Re: Newbie question: Are any differences between Chrysler Nissan Diesel SD33 and Patrol 160 series S

    I can't send a higher resolution as the file is too big for the forum.
    You will have to pm me your email address so I can send the bigger file.
    I don't have a torque curve for the motor.
    I run at...
Results 1 to 20 of 53
Page 1 of 3 1 2 3