Logo

Search:

Type: Posts; User: Bt Doctur

Page 1 of 4 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    8
    Views
    62

    Re: Volvo Penta fuel issue

    except the high pressure and low pressure look exactly alike
  2. Replies
    6
    Views
    15

    Re: 1985 3.8 removal

    #35 V8 is the same
    https://www.l-36.com/pdf/manuals9/omc_7.png
  3. Replies
    6
    Views
    15

    Re: 1985 3.8 removal

    If you can get to the bottom of the dust cover and remove the bell housing bolts AND IF THE COUPLER IS NOT RUSTED TO THE INPUT SHAFT motor pull forward and up /out
  4. Replies
    6
    Views
    15

    Re: 1985 3.8 removal

    https://www.l-36.com/pdf/manuals9/omc_13.png
  5. Replies
    1
    Views
    29

    Re: Raw water inlet hose

    best bet is a good auto parts store and make one up .Doubtful after 60 years there is one in stock anywhere
  6. Replies
    6
    Views
    15

    Re: 1985 3.8 removal

    Depends, if a stringer ,you can just remove the engine ,on a Cobra you need to remove the drive first
  7. Replies
    3
    Views
    42

    Re: AQ171c Plug wire placement

    If you mean the flat cap ,stand by
    https://i.postimg.cc/MnQndvVH/original.jpg

    https://i.postimg.cc/jL9WHzWB/v6.gif
  8. Re: Hi i have question that i am sure the guru on here will know the answer to

    doubtful a v6 will operate a jet
  9. Replies
    9
    Views
    69

    Re: compression reading

    110-130 ish
  10. Re: Replaces Shift Cable Bellows, now stalls when not at Trailer Trim

    If the cable does not slide at all and you installed the clamp with the drive up the clamp is too tight, most use just a ty-wrap or you accidently glued the cable to the end of the bellow
  11. Re: Replaces Shift Cable Bellows, now stalls when not at Trailer Trim

    what type of clamp used on the bellows where the cable enters the bellow
  12. Replies
    1
    Views
    56

    Re: haunted 4.3 volvo penta?

    ign switch shorting out
    slave solenoid/relay shorting out
    starter solenoid shorting out
    battery cable at starter contacting the yellow/red wire on solenoid
  13. Replies
    1
    Views
    40

    Re: gimbal bearing

    just pulls out from the rear
  14. Re: Knock sensor location and mystery bolt location

    1 probable only have one knock sensor
    2 that is where the oil pressure sender for the gauge goes or if the sender is on the port side near the oil filter then plug the hole at the manifold/block...
  15. Replies
    2
    Views
    44

    Re: Shift Shaft Orientation

    if the control box is in full fwd its correct
  16. Replies
    1
    Views
    44

    Re: 1981 Larson tilt problem

    Stringers dont have trim/tilt sensors. full up or full down. If motor runs but no up travel inspect the clutch pack . Drive dosent care where it is....
  17. Replies
    9
    Views
    116

    Re: Distributer Cap and Rotor?

    retap for the next size , self tapping small screw or replace the dist body
  18. Replies
    2
    Views
    72

    Re: Wondering where this hooks up

    with the updated trim pump it goes nowhere, you should have the old style trim cylinders with the new type of trim pump. It was part of the reverse lockout system to lock the drive down in reverse...
  19. Re: 91 omc cobra 4.3 setting timeing after distributer gear replacement

    Yes ,you can install a dist and not worry about the timing and get the motor close and running but if your too advanced or too retarded you will damage the motor .
  20. Replies
    9
    Views
    116

    Re: Distributer Cap and Rotor?

    Nope, same cap much different cost
    Distributors cap and rotor kit features brass inserts and stainless steel rotor springs,designed to provide the best possible fit to ensure maximum...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4