Logo

Search:

Type: Posts; User: racerone

Page 1 of 4 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    16
    Views
    212

    Re: Interesting hole in crankcase...

    I try to make folks think.----Steer them in the right direction.---Prevent them from making expensive mistakes.----Often my advice falls on closed minds.
  2. Replies
    16
    Views
    212

    Re: Interesting hole in crankcase...

    Your friendly parts man will likely know that there is an issue with the diameter of the wristpin.----And he may know what to do about it too.----Do you have a tachometer in your boat ?----What boat...
  3. Replies
    2
    Views
    34

    Re: 1963 Evinrude 3302 cooling

    See the wee holes / slots on the back of the exhaust housing ?-----Water should spray / mist out of there.------If you do not know age or condition of impeller you need a new one.-----Reason is that...
  4. Replies
    16
    Views
    212

    Re: Interesting hole in crankcase...

    Nope---The 60 HP blocks have 3 intake ports as opposed to 2 for the 55 HP of 68 / 69.-------There were lots of failures on the factory 60 HP pistons too.-----They sorted this problem out in the mid...
  5. Replies
    7
    Views
    76

    Re: 57 35 hp seahorse

    Just about any starter / alternator shop would have brushes that fit or can be filed to size to fit.-----That is if you can find such a shop.----The one local to me is now CLOSED.-----Too much...
  6. Replies
    7
    Views
    76

    Re: 57 35 hp seahorse

    I believe the Johnny said that he manually operated / opened the compression release valve while cranking it over with the electric starter.-----And I agree that the starter might need inspection /...
  7. Replies
    4
    Views
    54

    Re: Merc 2.5 HP 2 Stroke Cooling Problems

    Are you testing this on a boat or on a stand / bucket / 45 gallon drum ??
  8. Replies
    5
    Views
    70

    Re: 35 Evinrude, Flywheel Locking Down

    Well then-------Remove sparkplugs.-----Remove flywheel.------Put flywheel nut back on.---------Turn crankshaft.-----Report what you find then.
  9. Re: 1978 25hp evinrude. from full revs to idol while still at full throttle???? fuel system??

    No money spent ------- check the flywheel key.
  10. Re: 1978 25hp evinrude problems with fuel system i think

    Why did you pick on the carburetor first thing ??------What do you mean by " spark arrestor adjustment " here "-----Did you replace the water pump impeller ?----Did you operate the manual fuel pump...
  11. Replies
    4
    Views
    64

    Re: Johnson 40hp 89 model j40tecec

    The primer is an electric valve.-----It replaces a choke flapper.-----Motor will run fine without that primer once it is running.
  12. Re: 1968 55hp torn down, thoughts on how to proceed

    Some folks appear to doubt my statements.-----I have seen this failure numerous times !
  13. Re: What is the effect of the flywheel being in the wrong position?

    I believe there are magnets on the hub of the flywheel.------Those have to do with timing of the spark.-----No doubt you know what that means !
  14. Re: What is the effect of the flywheel being in the wrong position?

    If it was a splined crankshaft then there is one tooth that is missing.----You can not install the replacement in the wrong position.-----Unless of course you did not look and used brute force !
  15. Replies
    12
    Views
    147

    Re: Need some advice.

    Spark / fuel / compression ----I believe your motor should run.
  16. Re: No throttle while running 1996 200 hp Johnson

    Check for spark.-----If you only have spark on one side then check shift interrupt switch.
  17. Replies
    12
    Views
    147

    Re: Need some advice.

    Does spark jump a gap of 6 or 7 mm, yes or no ?-----Laying plugs on the block is NOT a good test of magneto output !
  18. Replies
    12
    Views
    147

    Re: Need some advice.

    You say you have " spark "----Does the spark jump a gap of 1/4" or more, yes or no ?
  19. Replies
    12
    Views
    147

    Re: Need some advice.

    In 64 they started the 9.5 models and a carburetor from one of those would not fit on a 1963 model.------It is confusing as to what you are trying to do.----And reed valves have nothing to do with...
  20. Replies
    3
    Views
    80

    Re: Noise in Mariner

    I would remove the exhaust cover on the side of the block.------About 20 bolts.----Allows you to see pistons & rings.
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4