Logo

Search:

Type: Posts; User: TheBrain

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    1,604

    Re: Fix rusty trailer or ?????

    I'm all for fixing up stuff that's worth fixing. I'm in agreement w/ replacing.

    you're lucky to have gotton her home the axel is eaten in half, kindof ballsezy one good bump in the road and snap...
  2. w/ the tang washer is a outer bearing washer required?

    I have two different spindles both 84

    > #1. is old fashioned cotter pin and casle nut I know there is a washer ontop of the outside bearing.

    > #2. is a tang type washer cotter pin combined.
    ...
  3. Replies
    0
    Views
    399

    Installing a kicker?s

    Installing a kicker ?s

    Well Iím finding out you donít just slap a kicker on and call it a day.



    Vesselís hull is aluminum (otherwise Iíd have a in hull ducer) 22í (add 20Ē main engine...
  4. Replies
    3
    Views
    890

    Re: must transducer be on starboard side?

    ray marine has a extension cable.

    main concern is turbulence w/ a starboard kicker interfering w/ the transducer. thanks TB



    additionally are all 9.9-15hp kickers are right hand rotation...
  5. Replies
    3
    Views
    79

    Re: New Mercury 2017 9.9 pro kicker ?s

    bad news incomplete engine missing electrical piece that plugs into the white square terminator.

    there is a large round wire harness the extension plugs into round opposite end is the white square...
  6. Replies
    3
    Views
    79

    Re: New Mercury 2017 9.9 pro kicker ?s

    9.9 pro kicker
  7. Replies
    3
    Views
    79

    Re: New Mercury 2017 9.9 pro kicker ?s

    I bought the merc. fuel fitting it doe's appear a tad different compared to the evinrude.

    still waiting on merc advice on longer gear shift cable. the engine will come w/ a steering cable...
  8. Replies
    6
    Views
    881

    Re: Couple ?s on 8HP kicker engines

    I decided to get a 2017 mercury 9.9 none tiller it has a small binecal trim ignition 25" shaft.

    so I'm looking into garlic type mounts for star side. still could build the final stage of my...
  9. Replies
    3
    Views
    79

    New Mercury 2017 9.9 pro kicker ?s

    New Mercury 2017 9.9 pro kicker ?s so far I have very limited knowledge of the merc.

    this will be the first kicker I've mounted.

    Iím purchasing a new to me kicker a merc. None tiller. Control...
  10. Replies
    6
    Views
    881

    Re: Couple ?s on 8HP kicker engines

    late 80ies is as about as old as I'd like for a engine. here's image of tuffboats roll cage
  11. Replies
    6
    Views
    881

    Re: Couple ?s on 8HP kicker engines

    I like the Honda engines and have found out the 8HP weights the
    same 105LBs as the 9.9HP.

    yes I have read about the compression release on the 4strokes on a percentage how much easier pulling on...
  12. Replies
    3
    Views
    890

    must transducer be on starboard side?

    must transducer be on starboard side?
    dragonfly pro5/ 22'pocket cruiser 70" beam
    I have one main 175hp engine w/ a standard right hand propeller the transducer is mounted on the starboard side just...
  13. Replies
    6
    Views
    881

    Couple ?s on 8HP kicker engines

    Couple ?s on 8HP kicker engines

    1.Do manual start kicker engines have alternators?

    2.I believe the manual start engines donít have alternators but do have magnetos so there isnít any option...
  14. Replies
    14
    Views
    5,181

    Re: Tires wearing bad

    dam I had to cut 1/4" off the rear axle for the new spindel install if you look closely the shorter axle can be sean.

    edit: only one side is a 1/4" shorther. I'll keep a close on on tire wear.
    ...
  15. Replies
    14
    Views
    5,181

    Re: Tires wearing bad

    hopefully it's OK to bump old thread.

    my question if the rear axle is 1/4" shorther than the front (but still rolls balanced) will cause abnormal tire wear?TB
  16. Re: eleavate the back of hull to lower the front?

    image of welded brace.

    took tad over one hour for the brace, then progressed my floatation pod project.

    I will order eight 3 1/2" 3/8 stainless steel bolts so underneath brace is supported...
  17. Re: eleavate the back of hull to lower the front?

    Update: I had the cross brace welded along w/ a stress crack in frame that was created when the rear brace cracked.

    On the way home I stopped at a trailer service shop mainly catering to semie...
  18. eleavate the back of hull to lower the front?

    I believe all of my vessel's weight rests on the rear axle. there is a 1/2" gap at front of bunks. this unloaded front leaf spring suspension created a huge vibration of the front part of I-beams...
  19. Replies
    23
    Views
    974

    Re: After market engines trim switch?

    I tell people (none boaters) that if kindof favorable none south winds (less than 10Kts.) I can go to the Gulf for a week however mite be able to go offshore 2 or 3 times during this week, it's a...
  20. Replies
    23
    Views
    974

    Re: After market engines trim switch?

    dam I thought I did something and save a couple bucks o'well. hopefully it will last a few seasons.

    I usually always wear rubber soled sneakers but I'll beware of the shock hazard thanks for heads...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4