Logo

Search:

Type: Posts; User: racerone

Page 1 of 4 1 2 3 4

Search: Search took 0.13 seconds.

  1. Re: 90 Evinrude 150HP 2 stroke - Carb Primer/Choke inlet barb broken

    I should set up the lathe and make 50 or so of these fittings.
  2. Replies
    1
    Views
    11

    Re: Bypassing VRO automatic oiling system

    The 84 models did not come with VRO.-----But look up the 1983 / 84 pump and install it----- model # of your motor is ?
  3. Re: 1978 40 hp mercury water around top plug

    Step # 1 is to replace the water jacket gasket.----Easy job on a fresh water motor.
  4. Replies
    13
    Views
    52

    Re: 19?? Evinrude 4 hp

    Is the CO actually a CD , yes or no ?
  5. Replies
    87
    Views
    1,108

    Re: 77 Evinrude 85 h.p , will not idle

    Keep us informed on the progress.
  6. Replies
    13
    Views
    52

    Re: 19?? Evinrude 4 hp

    ??------100:1 is a ratio.--------Nothing to do with metric measurement.-----And you should run it at 50:1 ratio.------Calling or dropping in asking that information is still interupting a busy...
  7. Replies
    13
    Views
    52

    Re: 19?? Evinrude 4 hp

    They just do not want to be bothered by those calls today.----The CO makes it a 1985 model.----Every boat shop knows that !
  8. Replies
    12
    Views
    84

    Re: 1956 Johnson Seahorse 15hp

    You also need to adjust the low speed needle to compensate for fuel and local atmospheric conditions.-----The factory / book settings are only to get the motor to start and keep running.
  9. Re: 2003 Mercury 125 Saltwater - Replaced Oil Level Sensor, Alarm Won't Stop

    Does the alarm buzzer have an electronic circuit?-----If so then perhaps the buzzer itself failed.
  10. Re: Plz help. Pival thing at steering cable end

    Need to post pictures.-----This should be an easy thing to solve once we can see what you are trying to do.
  11. Replies
    2
    Views
    26

    Re: 1998 Johnson 150 won't run

    Pushing the key in while cranking it over ?
  12. Re: 1976 evinrude 70 hp outboard trim/run switch

    Model # is ?-----Any pictures of the trim / tilt system on this motor ?
  13. Replies
    9
    Views
    92

    Re: help to identify my mercury

    There are not many air cooled Mercury motors.----Stop running it .-----Post a picture or what horsepower is it ?
  14. Replies
    18
    Views
    158

    Re: 1990 40hp Mariner weak lower cylinders

    The whole concept of crankcase compression is mis-understood by many folks.-----Difficult to trouble shoot for some.
  15. Re: Evinrude 15hp model 15604A motor issues

    There is no SWITCH BOX on that motor.
  16. Re: 1985 Mercury 18 XD fast idle adjustment

    The picture in post #1 does show the mixture screw for low speed performance.----The poster says that idle is a " bit rough " and adjusting the mixture may help smooth it out.
  17. Replies
    4
    Views
    49

    Re: 1985 Johnson 70hp 2 stroke no start

    Are you raising the fast idle lever ?-----Are you pushing the key in while cranking it over ?----Checked the kill switch?
  18. Replies
    18
    Views
    158

    Re: 1990 40hp Mariner weak lower cylinders

    Any evidence that this motor was apart before ?---------Perhaps remove intake port bypass covers to see if you can spot something there.-----Put tape over those cover openings and pull motor over to...
  19. Re: 1985 Mercury 18 XD fast idle adjustment

    The knob in yellow adjust idle timing.-----Screw item 16 on front / upper part of the carburetor adjust slow speed mixture.----There are lots if items identified as #16 ( carburetor repair kit )...
  20. Re: '95 Mariner 75hp struggles to get above 3800rpm

    Flywheel key checked ?-----Cylinder sleeve position checked ?-----Crankcase compression checked ?-----Reed valves checked ?-------Tried removing plug wires one at a time to see if all cylinders are...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4