Logo

Search:

Type: Posts; User: papyson

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    15
    Views
    3,436

    Re: Contaminated Gas

    a lot of factors in play here...is the gas ethanol?..are you positive it was treated?..do you have a water filter installed?..was the 100 gal tank full of old gas or did it have a partial tank?...
    ...
  2. Replies
    13
    Views
    842

    Re: Mystic Lubricants

    replied to your private message
  3. Replies
    13
    Views
    842

    Re: Mystic Lubricants

    http://www.wholesalemarine.com/johnson-evinrude-premium-blend-gear-case-lube.html?gclid=CJbvpMrym84CFQotaQodjYIG6A
  4. Replies
    13
    Views
    842

    Re: Mystic Lubricants

    Why not use recommended supplies and oil and plugs etc recommended by the engines manufacturer?...an outboard engine is a high rpm piece of equipment that's easily damaged and playing around with...
  5. Re: Minn Kota Riptide 80 lbs - Battery size / Range

    13797if its a 12volt motor you will need a minimum of a 100 aph battery to run 4 hours at medium speed with no current or...
  6. Replies
    7
    Views
    827

    Re: Kohler gen not working under load

    let us know please
  7. Re: 1995 Evinrude No start, new starter, solenoid , battery, and cables.

    ok..we are back to square one...please take the voltage readings again...
  8. Replies
    7
    Views
    827

    Re: Kohler gen not working under load

    I miss read ....I thought you were running a 4kw..it doe not matter on the basic question in rpm when running...

    the other two things are regulator and flashing the windings....the web is full of...
  9. Re: 1990 Johnson 88SPL bogs down at 1/4 throttle when cold

    have you checked spark with a spark gap tester?spark should jump 7/16 inch with a good pop..i would also put an inductive timing light on each plug wire to double check its running on all 4 at...
  10. Re: 1990 Johnson 88SPL bogs down at 1/4 throttle when cold

    lotta looks but no answers...a question....is the bulb pumped hard before start?..what is your start procedure?..i ran a 88 from 1994 to 2011...
  11. Replies
    3
    Views
    307

    Re: BF 130A - Tachometer Does Not Work

    thanks mike..i am going to have to stop my entries before coffee kicks in..over looked brand of motor..
  12. Re: 1995 Evinrude No start, new starter, solenoid , battery, and cables.

    if ''key on'' was key turned to start then I would suspect either a high resistance from the battery positive post to the starter.a defective solenoid (if it was picked), or an open starter...it...
  13. Replies
    3
    Views
    307

    Re: BF 130A - Tachometer Does Not Work

    the tach works off the regulator..what does the voltmeter read when running?...
  14. Replies
    7
    Views
    827

    Re: Kohler gen not working under load

    I had a 1973 identical kohler on a boat I purchased in 1973...the only problem I had with it was flaky auto charge for the battery..rewired it to where it charged max when ever it was running which...
  15. Replies
    9
    Views
    235

    Re: Forgot drain plug today

    we all have done it..over the years I have developed a launch routine...first of all I want no help or talking or distraction of any kind..i,and I alone will, prepare the boat for launch...I store...
  16. Replies
    18
    Views
    1,474

    Re: More trouble from my 88 50hp force

    it don't have anything to do with the current problem but it looks like in the pics that the motor is setting too low on the boat..almost as if you have a long shaft engine on a short shaft boat..
  17. Replies
    12
    Views
    812

    Re: 55hp 2 stroke jetting

    reread and think you may be right...if so my bad...
  18. Replies
    4
    Views
    310

    Re: 2000 Johnson 90HP Alarm

    warmer water and warmer air?
  19. Replies
    2
    Views
    2,903

    Re: Bow eye plate 5m aluminum boat

    new aluminum eye plate backed up by an aluminum plate inside the hull...I have gone this route twice on two different boats..the reason for the aluminum eye plate is you are then welding aluminum to...
  20. Re: Over Heating at 6000RPMs and Motor slightly tilted

    http://www.saltawayproducts.com/OutboardFlushingPage.htm

    you may try this...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4