Logo

Search:

Type: Posts; User: racerone

Page 1 of 4 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    1
    Views
    10

    Re: Getting a new USED boat up and running

    Kill switch in the " run " position ?
  2. Replies
    5
    Views
    32

    Re: Johnson 50hp no spark

    edited
  3. Re: 1977 Evinrude 85 horsepower intermediate fire but runs great once started

    No need to pull flywheel to test stator and sensor coils !!----I would load test your battery and take the starter motor apart for inspection !
  4. Replies
    3
    Views
    35

    Re: 1970 johnson 20hp.

    Sounds like it is jumping out of gear.-----So do the following.------Remove the wee cover on the side of the exhaust housing.----Now remove screws in brass piece one at a time.----Make sure notch is...
  5. Re: Chrysler 75hp Bearing Cage or Lower Unit

    Your location ?
  6. Re: Bearing Carrier Puller 1983 4.5 HP Evinrude

    On a fresh water motor I bump the housing so it rotates a wee bit.------Then gently bump the housing tabs to take it out.---Or put propshaft in a vice and bump the gearcase housing to take it...
  7. Replies
    4
    Views
    35

    Re: Mercury 60hp 2 stroke issues

    Replaced the water pump impeller ?-----Inspected the reed valves ?----Does spark jump an actual gap of 3/8" ( 1 cm ) or more , yes or no ?----The new CDI unit was a factory part or a " special price...
  8. Re: intermitted spark runs great and then like poop.

    Sorry----I can not stand beside your motor to diagnose it.-----I just toss out wild / no money spent ideas for folks to check out.----Good luck with your motor.
  9. Re: intermitted spark runs great and then like poop.

    Perhaps the S.L.O.W.----system kicks in.-----Bad sending unit.------Worked on a 1998 model 70 HP last week where somebody had run the motor with no cooling water to the impeller.----So also check...
  10. Re: Yamaha Outboard Water Hose goes to nowhere

    That question is asked here about every 3 weeks or so.----That wee hose is for a speedometer.-------My project boat will be using a GPS speedometer with just a 12 volt lead going to it.-----No need...
  11. Replies
    4
    Views
    46

    Re: 9R69S Throttle handle question

    MIKEY------The 9.5 HP models have a stop button on the front panel.-----From 1964 to the 1973 models.
  12. Replies
    4
    Views
    46

    Re: 9R69S Throttle handle question

    It does not spring back.-----Pop the flywheel off to inspect the coils.
  13. Replies
    3
    Views
    35

    Re: torque for bearing carrier

    Try----100--- INCH LBS
  14. Re: 1989 Johnson 175 shift and throttle hook up

    ???----Try installing the piece in front of the carburetors.----Should be obvious then !!
  15. Replies
    2
    Views
    39

    Re: 2000 Johnson 70 HP 2 cycle

    Try 102.5 FT LBS
  16. Re: Timming advance question 1976 Evinrude 75643D 75hp Outboard

    Well---Imagine that redline with no load.-----That motor will do that running on 2 of 3 cylinders.----That proves nothing and may in fact cause damage to your " rebuilt motor " ----Good luck with...
  17. Re: Timming advance question 1976 Evinrude 75643D 75hp Outboard

    Sounds like it may be running on 2 of 3 cylinders.------A local shop may have what is called a " test prop " designed to load the motor as if the boat is moving !!----Used just like the way you are...
  18. Replies
    3
    Views
    36

    Re: Honda bf15a rebuild

    Have to ask.----Was throttle open when compression testing ?------These motors run with very little valve clearance.----Often with wear you end up with valves that are not quite closing and burning...
  19. Replies
    1
    Views
    32

    Re: 1999 100HP Yamaha with Ford motor

    ??----Perhaps a YAMAHA motor built for FORD -----Think SHO model.------Also used by YAMAHA for their outboard models.
  20. Re: Motor loses pee stream above 3/4 throttle

    Part 79799 might be the problem and of course NLA.----Might have to look into making them / having them made for me.
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4