Logo

Search:

Type: Posts; User: racerone

Page 1 of 4 1 2 3 4

Search: Search took 0.14 seconds.

  1. Replies
    5
    Views
    343

    Re: 85ESL69S Base Plate Assembly Binding

    Has water pump impeller been replaced recently ?-----Overheat warning light tested ?------How much end play on the crankshaft ?-----Or can you lift flywheel up and down ?----Dial indicator on it...
  2. Re: 2002 Mercury 50 4 stroke carb float needles

    Take a very good look at the operation of the float and float valve.-----I think you might have problems elsewhere.
  3. Replies
    2
    Views
    17

    Re: Diagnosing Evinrude 75 Problem

    Electronic / electrical parts availability can be an issue for newer motors.
  4. Replies
    2
    Views
    17

    Re: Diagnosing Evinrude 75 Problem

    An E-tec is a 2 stroke motor.-----Hard to figure out how a stator and fuel pump are both defective.----Fuel pump diaphragm is about $16.00.----But check and see if stator is available.
  5. Replies
    1
    Views
    12

    Re: Evinrude spring

    The one side just goes in a hole in that arm.-----The other side slides in a groove on a post.------
  6. Replies
    8
    Views
    38

    Re: Spark plugs for a mid-80s Merc XD

    Does the motor have the copper / bronze decals ?----Canada is fairly big I heard.----Takes me 24 Hrs driving to get out of Ontario if heading west.----If impeller has not been replaced recently you...
  7. Replies
    2
    Views
    16

    Re: Mercury 500 Needle valve

    -I do not believe you should start " messing " with springs.
  8. Replies
    8
    Views
    38

    Re: Spark plugs for a mid-80s Merc XD

    It needs a new a new impeller !----Find it right here on this site.------" engine diagrams "-----And just a few clicks.
  9. Replies
    8
    Views
    38

    Re: Spark plugs for a mid-80s Merc XD

    So it has the copper / bronze colored decals ?-----Start with a compression test.----Post the numbers here.-----And it will need a new water pump impeller.-----Most of those I look at have an...
  10. Re: 1997 BF15 fuel delivery problem or stuck valve/lifter?

    Well----I thought it was a spark issue in post #2
  11. Re: 1973 Evinrude Triumph 65HP(65373R) Weak spark

    Inspection and testing is what you have to do.
  12. Re: 1973 Evinrude Triumph 65HP(65373R) Weak spark

    Your compression is way too low.----Test with another gauge.------Or compared to all the money and frustration a head gasket is cheap , cheap.----Pull the head off and have a look at cylinder walls
  13. Re: mercury 5 hp 4 stroke propshaft bearing removal/installation

    Use heat ( boiling water ) and bearing can easily be removed I think. --- long punch and small hammer.
  14. Re: Evinrude 15hp fuel pump rebuild - Chinese core?

    You get what you pay for.------Your location ?-----If in Cansda-----evinrudeparts.ca -----might help you.
  15. Re: How to open Carburetors 1994 Force 120 Outboard

    Post a picture of the control box.----Most have a feature to disable the shift and open throttle for starting !-----A knob you pull out perhaps.----But I can not see your set-up.
  16. Replies
    3
    Views
    39

    Re: Lower End Unit Water Stream?

    Normal.
  17. Replies
    1
    Views
    31

    Re: 1995 Johnson 70 hp ignition problems

    A maximum ignition output test should be done.---Set gaps on a test device at 7/16" ------Do it cold and perhaps when motor falters.--------Leave plugs in.-----Crank motor over and observe spark.
  18. Re: Water inlet on 2003 Johnson 15hp 4 stroke

    Look above the propeller.
  19. Replies
    2
    Views
    32

    Re: QD 21 1960 Johnson 10 head bolts

    Just go to a hardware store and get a stainless bolt.----Why would they not take any torque ??
  20. Replies
    4
    Views
    64

    Re: 25hp 3cylinder starts in reverse

    Is the lower shift rod fully screwed into the lower unit ?-----And you may have to adjust the upper shift rod.
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4