Logo
FULL SITE MENU

Recent content by scruffy63

  1. S

    91 Johnson 9.9

    I have a 1991 Johnson 9.9hp that has QL77JC4 plugs but my books don't o that high an I don't know if they need set at .30 or .40 can u advise?
  2. S

    25hp Johnson pops or misses at idle and above

    1972 Johnson 25 hp has a pop or miss at idle and just above before going in gear. I have cleaned carb and tried opening air screw a bit but it has it after starting and running a minute. I have before cured this on others by opening air more but this does not seem to help.
  3. S

    Flywheel Key Breaking

    I have a 1973 Johnson 25hp Recoil start that is constantly breaking the flywheel key. I can't find anything wrong. Flywheel is tightened correctly and key is correct. Any help?
  4. S

    No gas to carb on 15hp

    I have a 75 evinrude 15hp that has 110 pounds compression on both cyls. New fuel pump and carb rebuilt. Question is when I disconnect the fuel line from carb and have it hooked to fuel tank and turn engine over with socket on electric screw driver there is no gas pumping from fuel line. Thus no...
  5. S

    1972 Johnson 25hp rings?

    I have a 72 Johnson 25hp that needs rebuilt. Standard rings are Non-pressure back and Pressure back. How do I know which ones I need?
  6. S

    79 Chrysler 20hp carb problem

    I have a 1979 20hp Chrysler mod. 206H9B, I cleaned the carb as it had been sitting for several years. When I first started it before cleaning it would run a few seconds working the choke as it started. So I took it apart and there was crud in needle hole and so forth. I took out the idle screw...
  7. S

    Johnson 15hp no power

    I have a 79 Johnson 15hp that has 110 lbs compression both cyl's, new coils & powerpack. Has great spark, carburetor has been cleaned and float has been set per gauge, new fuel pump, starts easy and idles great but on boat it lacks speed as others I have worked on. I have tried various settings...
  8. S

    parts

    I have a sears eska 7hp that I need a carburetor kit for but all the sites don't ley me enter model number to search parts. Any help in finding carb kits?
  9. S

    Front bearing race removal

    Is there any way to remove the front bearing race on a 15hp Johnson lower unit with out the $212. tool that is advertised? Tool number is 391259
  10. S

    71 Evinrude 9.5 problems

    I have a 71 Evinrude 9.5hp that has good compression, new coils new points & condensers and plugs. I cleaned carburetor and blew out all valves after soaking in cleaner. Reset the float at 13/16 level and drop at specs. New fuel pump and gas lines. Starts easy when choked BUT when choke is...
  11. S

    Shift rod bushing removel

    I have the tool to take out shift rod bushings on most lowers but I have an Evinrude 25hp that has the shift rod where the tool won't pull it from the bottom because there is cast housing below the bushing and seal and the puller won't work on the one. Question is how do I get that bushing out?
  12. S

    Ouestions again, I can't find problem

    I have a 5hp Briggs & Stratton outboard motor that Surges, I can't find any service shops to ask questions about it. No help searching the briggs sites. I was told it may be a speed limiter but the manual I bought does not even cover that. And finding a speed limiter is a problem. Carb is new...
  13. S

    5hp briggs & stratton outboard problem

    I have a 5hp briggs & Stratton outboard that surges filter throttling up from ide. I have a new carburetor on it and new fuel pump and filter. It starts and idles fine but when I power up it surges badly. Get compression and spark. I saw a post some were that someone had that problem and it was...
  14. S

    5hp briggs & stratton outboard problem

    I just got a 5hp Briggs & Stratton 5hp and it needed a new carburetor so I bought a new one and after installing the new one I have the idle set where it runs smoothe and idles slow. It starts easy and runs good until I get just about half way open then it stumbles and surges and back fires. any...
  15. S

    9.9 Sears Gamefisher

    I have a sears gamefisher 9.9hp that has model # 217-586251 and need an impeller. I can't find where to buy one. these are small impellers not much wider than an inch. Any help would be great.
See more
Back
Top