Logo
FULL SITE MENU

Recent content by scott_s

  1. S

    turbo jet parts

    need impeller shaft for '94 115 turbo jet. part #0340340 nla from OMC. any ideas?
  2. S

    O.M.C. Turbo jet looking for parts.

    trying to find an impeller shaft (#0340340) for a '94 115 turbo jet. this is n.l.a. from omc. any steers would be appreciated.
  3. S

    Chrysler sterndrive parts

    any one have a source for 300 drive parts?
  4. S

    thunderbolt IV issues

    boat started dropping cylinders after warming up. finally lost spark completly. replaced coil, and ran good about 3-4 hours. same issue returned. later when I checked boat, spark was ok. left it running at the dock. 1 hour later returned, engine stopped, no spark. boat brought to my shop, and...
  5. S

    5.7 GI-E general warning #1

    oil pr. good. oil level ok. temp ok. no knock detected. sets gen warning #1 and goes into R.P.M. reduction (S.L.O.W.) using rinda scan tool. any ideas?
  6. S

    Bravo one prop spline

    "hey guys. far from home, with "hey guys. far from home, with a terrible internet conection. just one simple question. what is the spline count on a bravo one drive propshaft? in a hurry. apreciate the help. scott stephens."
  7. S

    1964 Ted Williams

    "young guy who works for a fre "young guy who works for a freind recently came up with this motor. (got it from his granddad) model #574.60100 ser.#64600710-7230 (7 1/2 h.p.) ted williams made by McCulloch. thing looks brand new. has all the original paperwork. good compression, etc. He wants...
  8. S

    Remove just the lower unit

    "just completed a job today. c "just completed a job today. customer replaced his own water pump. (alpha 1) removed just the lower, left the upper bolted to the bell housing. would not go into fwd. gear. must have jammed something putting it back on. the shift crank was bent. had to completly...
  9. S

    Causes of high compression J200 ES 96

    "have an engine in shop. prett "have an engine in shop. pretty well worn out. checked compression. two cyls. 105/ 106 psi. three are low 90s (lowest is 92) one cyl. checks 126 psi. I have not removed head, plenty of other problems, this thing needs rebuild. any ideas about high comp? (cyl. 4 )"
  10. S

    A cautionary tale for DIYs

    "just completed a job for a D. "just completed a job for a D.I.Y. He installed his own long block. couldn't figure out wiring harness. brought it for me to install. old engine had mech. fuel pump. new needed electric.(oops)elec. fuel pump(ordered by cust.) was designed to bolt on exhaust elbow...
  11. S

    Awright you guys

    "exhaust gasket, starting prob "exhaust gasket, starting problem, charging problem. two strings apiece. cut it out."
  12. S

    The perfect prop

    "3500 is good. normally best c "3500 is good. normally best cruise=75% throttle. (approx) my point is, adding pitch would probably cause loss of both mileage and speed. if You feel You must try, find a dealer who has test props. then testing will not break the bank. 4200 revs should do no...
  13. S

    Andrew re gimball housing repair kit

    found source for mcm transom r found source for mcm transom repair kit if You need. S.
  14. S

    GLM manifolds

    "considering selling GLM manif "considering selling GLM manifolds. Prices are pretty good, have 3 yr. warranty. any input, good or bad would be greatly appreciated. Haven't used them before, and don't want to sell my customers junk. thanks, S."
  15. S

    Ujoint bellowtransom assyrepair

    "help, my mind is failing. I&# "help, my mind is failing. I'm looking for a repair kit for mcm transom/ u-joint bellows. it's a patch for a partly broken ring at transom assy. where bellows attaches. consists of a plastic/ nylon ring that fits over casting, epoxy, and a bellows. I know it...
See more
Back
Top