Logo
FULL SITE MENU

Recent content by Portis Left

  1. P

    Specific RPM question

    I have a very specific request. I need to know the optimal wide open RPM operating range for my specific engine. It is an evinrude 1978 200 hp........ serial#. 200849R. I just can't find it on google. Very thankful in advance...
  2. P

    Buying a prop

    Please can someone give me the lowdown on all I need to know about buying a prop before I actually do it. I tried putting my merc prop on it and splines were good....but the body was smaller and it didn't leave room for the nut. Is it really that complicated?
  3. P

    Evinrude identify...need to buy a manual

    Hey guys, i have acquired an evinrude 200 hp motor. From comparing it to you tube videos it looks like around a 76. I don't feel like it will be hard to identify...but I need exacts to buy a how to manual and parts. At this time I need a clutch dog. But I need to know all the specifics to...
  4. P

    engine acts funny after lengthy run

    i just got this motor running like a champ by the advice of good people on this forum. last saturday before leaving the lake i decided to take a longer run to use up some of the gas i had purchased previous sessions and never really got to run out. MY PROBLEM IS: after a 12 to 15 minute run...
  5. P

    ignition components and their purpose

    ok guys....the thread is back with many answers i havent answered yet. 1. the firing order is correct. https://youtu.be/4wAnSk3Yi_8 2. cleaned the cap/rotor. pic included of cap just for reference. 3. my TDC is exactly on the zero....without me moving it. 4. i included 2...
  6. P

    ignition components and their purpose

    things i know so far: plugs----L76V prop has a wierd run of number----48 773 1? A1 19 i went to check the cap wires and found that 2 were still connected but i could tell they had been pulled out without untwisting before. solder was still attaching it but was pulled out...
  7. P

    ignition components and their purpose

    ok guys. is this the power port hole? if so i apologize. the whole time i was thinking this was the wrist pin hole. i got my finger behind the piston wall where this hole would slide and i DID feel a dip where the cylinder is definitely not round. as always.....gratefully waiting for your...
  8. P

    ignition components and their purpose

    guys i got em. this is the right panel correct? i dont know what you could possibly tell from this but...let me know..sorry theyre sideways
  9. P

    ignition components and their purpose

    and the carbs ARE 22s i found a pic from when i rebuilt them
  10. P

    ignition components and their purpose

    updating: all cylinders compression between 117 and 122. i did this cold. should i do it hot? also found another number about an inch below my middle cab. is this a serial number?(pic) and if i am not mistaken.....the jet i was supposed to find has 80 on it? (pic)
  11. P

    ignition components and their purpose

    my motor has this issue. cranks and idles great. but from half way to full throttle(say 45 degrees forward) to full throttle(say 90 degrees forward) it only gets louder and runs at what seems to be a full bog condition. the carbs (3) "ARE" fully open when lever is pushed forward so i think...
  12. P

    find my year make model

  13. P

    find my year make model

    i need to try to get you guys to help me find this info on my motor. im sure this is a "here we go again" topic but i think this may be special case. the only number on this is not on the motor itself but on the part that mounts the motor to the boat. (transom bracket?) if im in the driver...
  14. P

    find my year make model

    hello good people..... i need to try to get you guys to help me find this info on my motor. im sure this is a "here we go again" topic but i think this may be special case. the only number on this is not on the motor itself but on the part that mounts the motor to the boat. (transom bracket?)...
See more
Back
Top