Logo
FULL SITE MENU

Recent content by paul

  1. P

    Omc trim and tilt help

    i was washing the boat out in i was washing the boat out in the drive and jacked the front of the boat up to far drove the motor into the ground . now my trim motor wants to run all the time down . if you try to run it up it does nothing then you let off the switch and it tries to go down . i...
  2. P

    OMC upper outdrive lost nut inside

    " I accidentally removed the s " I accidentally removed the screw from the left upper side of my 1990 OMC Cobra outdrive (4 cyl 135hp) and the nut that held screw on was not attached to the housing is now floating around in the upper (water cooling area) of the outdrive! I've been told my...
  3. P

    Joe 96 Johnson

    I could not pull up my messag I could not pull up my message to you so here it is again. I have a 96' Johnson FastStrike 150hp with a high end problem. The boat will run fine sometimes and other times I cannot get the boat to run over 4500rpm's. I've change plugs twice and the power pickup...
  4. P

    225 hp jonson 1996

    what should the compression b what should the compression be on this.thanks
  5. P

    Suzuki 4hp 2 stroke help

    ENGINE STARTS EASY RUNS FINE ENGINE STARTS EASY RUNS FINE UP TO HALF THROTTLE THEN IT STARTS TO SURGE THEN SLOW UP THEN SURGE IT DOES THIS VERY ERRATICALLY?? HAVE CLEANED THE CARB FUEL FILTER ETC BUT TO NO AVAIL. CAN ANYONE HELP??
  6. P

    Evinrude Jumping in and out of Gear

    I need to order several parts I need to order several parts. I read on an earlier e-mail what i think the problem is which is rounded lobes on shifting forks? My propblem is I can't find the year of the motor to buy the parts. I have a 75HP Evinrude Speed Four Electric start. Model # 75452A...
  7. P

    1993 Maxum Want to repower from V6 to V8

    " I have a 1993 Maxum 1900SBR. " I have a 1993 Maxum 1900SBR. It has a 4.3LX and I would like to repower to a 5.7. Can anyone tell me if this is going to be more trouble than its worth? How hard a swap would it be? Will my Alpha One drive handle the extra power? If I bought a crate motor...
  8. P

    Help

    " Hello I have a 1972 125 " Hello I have a 1972 125 electric shift evinrude that began leaking gearcase oil from the prop housing slowly. I have bought a manual for repair but while im waiting for it to be delivered i tried taking apart thelower unit to check the seals. I got the lower...
  9. P

    1989 Suzuki Exante V6 One side fires and runs

    " Got an 89 Suzuki Exante 200 " Got an 89 Suzuki Exante 200 V6; It was running fine and one day it idled down and almost quit but would not run much past idle speed. Got it home, let shop have it for a month, they couldn't figure it out.It will run, but only on one side.This motor does have a...
  10. P

    Gasket sealer

    " When changing the impeller o " When changing the impeller on a 1983 Evinrude 15 hp motor, do you put gasket sealer bewteen the water pump housing and the plate? Around the edges? If so what kind should I use? "
  11. P

    Water Pump

    How often should the impeller How often should the impeller be changed in the water pump? I have a 1983 15 hp on a sailboat. Do you have to use a sealer on the pump housing and on the shaft housing when you change the impeller? Thanks Paul
  12. P

    Engine Dies after running a while 15 hp Evinrude

    " I have a 1983 15 hp Evinrude " I have a 1983 15 hp Evinrude that now dies after it is running for a while. It seems that it is not getting fuel. I replaced the primer bulb this year on the gas line, and installed a clear gas fuel filter. When it first stopped running, the fuel filter was...
See more
Back
Top