Logo
FULL SITE MENU

Recent content by John M. Daniel

  1. J

    Inspection hatch install on Fiberglass Bass Boat

    I have a Klassic 1992 17' fish and ski that I need to install a round inspection hatch. Ideally, in front of the transom and the outboard in the area I call the back wash. This hatch will allow me to service and replace the Bilge and Aerator pumps much easier since the only access is from the...
  2. J

    Thread Locker for reed replacement

    I am replacing the reeds on a Force 120 HP and a Force 90 HP. What thread locker should I use on the reed stop screws, reed block to heat plate and adapter to power head? The manual says use red, or permanent, I am saying maybe better to use oil resistant blue, or medium strength. May want to...
  3. J

    3 blade or 4 blade on Force 90 HP SN#026494 M#908P91C

    Any pros and cons on going from a 3 blade to a 4 blade prop for better lift and earlier plane and fuel economy on a 17' bass boat? Would anyone advise on a pitch either 15 or 17? Using 17, 3 blade right now and the engine will tach out around 4600-4700 Thanks
  4. J

    Ignition switch replacement screw type connections

    I am replacing my ignition switch which has screw on connections with a new Sierra push to choke switch. Should I use a thread locking compound or some other dressing on the screw threads. I understand Locktite is an insulator, but there appears to be some type of thread dressing on the old...
  5. J

    1997 Force 120 HP neutral switch location Model 120 ELPT Serial OE264525

    Where is the neutral switch on this unit when equipped with a top mount Quicksilver 3000 remote control? There are times when I have to move the shifter in and out of neutral to get the switch to release and allow me to start the engine. I have looked at the manual and a diagram of the shifter...
  6. J

    Drive Shaft, Force 120 HP 1997, M#120ELPT Serial # OE264525

    I removed the lower unit to install a water pump kit. When I pulled the lower unit, there is no seal ring or wear sleeve on the shaft or stuck in the splines in the crank shaft. The parts list shows these each located on the shaft for this model. The drive shaft does not have the seal ring...
  7. J

    Shift Linkage adjustment !991 Force 90 HP

    I need a video on how to adjust the shift linkage on my 1991 Force 90 HP Model # 908P91C After discovering the middle shift rod was unscrewed out of the lower shift linkage, then reinstalling it properly, I need to adjust the linkage at the control cable connections on the power head. The unit...
  8. J

    Force 90 HP 1991 Model Tachometer problem

    When i got this boat, the tach worked. Now it does not ( several years later) needle jumps when I turn on the ignition, but the tach does not work. Where do I start to test or check for the signal from the engine? Thanks!
  9. J

    1991 Force 90 HP Shift linkage

    Does the linkage shift arm in the lower unit shift side to side?
  10. J

    90 HP 1991 Force 3 Carburetors install order

    I have rebuilt my 3 Tillotson carburetors on my 1991 Force 90 HP, got all the needed parts on MarineEngine.com. The bottom carb has always leaked since I bought the boat. When I reinstalled the carbs, it still leaked out of the overflow. I have studied the carb stock #s and notice the bottom...
  11. J

    Cowling sound blanket

    I need to replace the sound blanket inside liner on the cowling or "Hood" for the engine. Does anyone know of a replacement product and a source to purchase, Thanks!
  12. J

    Outboard Motor Cowling Sound Blanket

    I have a 1991 Force 90 HP. I need to replace the sound blanket inside liner on the cowling or "Hood" for the engine. Does anyone know of a replacement product and a source to purchase, Thanks!
See more
Back
Top