I ran my fresh Mercury rebuilt 1978 inline 6 this weekend and ran very nice except I used a lot of fuel 6 gallons in 1 1/2 hour. Throttling up and down cruising at various rpm's to break it in. I noticed that the carb. linkage that connects carb.1 to carb.2 and carb.3 are soaked with fuel. Which...
I am fixing to put a 90 hp inline 6 on a 1972 15 foot trihull starcraft that had a 80 and 85 hp inline motor on it before. The boat is rated for max 85hp.Will the added weight of an inline 6 make any great difference on the transom.I know back in the mid to late 60s Mercury made an 80hp inline...
I picked up a 1978 90hp inline 6 for next to nothing (0=$) and it looks good.There are however a few questions I would like to throw out here.With todays gas what should this one be set at for WOT degree wise.Also the switchbox looks to be damaged,is there a difference between 332-2986 inline 4...
I need alittle input on another project motor.A buddy of mine gave me a 85hp merc. that hasnt run in 5 to 6 years or more.All the wiring harness was rotten so pulled it all off and got a new one.In the process of getting this thing cleaned up I soaked the cylinders in 2 cycle oil overnight and...
just purchased a 1969 distributor in the hopes I could just change out the collar to match my carb setup.Well I was wrong now in order for this distributor to work I need the top carb cluster part number 52518 and this is NLA. anybody have any Idea's where these still can be purchased??
Will the Distributor from a 1970 merc 65hp model fit my 1972 merc 80hp.The 650 has the same style cdi ignition as mine just the distributor is a little different.I am pretty sure it will bolt up and work for my switchbox but I am not sure how it works with the carb link.
Due to low compression I would like go ahead and rebuild this motor serial number 3192882.My question is there a difference between low dome pistons and high dome pistons.Or does this only go for the inline 6's not the inline 4's. I was reading somewhere more torque with low dome pistons versa...
I know I will probably get bunch of different opinions on these plugs but your expertise is always welcomed.I am currently using NGK BUHW plugs but would like to get a new set due to renewing electrical componets(also still have a slight misfire).So my options are:
NGK BUHW
Champion L76V...
I am a little concerned about a new water pump.I ordered a new complete water pump and installed it.But before i put the lower unit back on I would like to know is it hard to turn the drive shaft after the new pump is installed.Mine sure is.I didnt wrench it down real hard,it just tight.Any...
I need a little advise concerning a new water pump I have a 72 80 hp merc with a early 80's 115hp lower unit and I need to purchase a new water pump/complete kit I found 2 but not for sure if these are right.The lower unit is with the tapered bearing style and has the speedometer hose on it.I...
I have been reading some of the posts and was wondering compression difference between 80hp and 85hp motors.On my 72 80 hp I am lucky to hit 125 psi and on some post I have read that the 85 hp motors are hitting 140/145 psi.Looking at some of the engine specs there isnt much difference between...
I went down to my local boat shop today to pick up some odd's and ends and we got to chatting about my Motor Merc.800 and I had mentioned that you guy's hear had helped me alot.Thats when the discussion went sour,he said these guy's will lead you on a wild goose chase and you will end up having...
Hello Guy's
I just took the side covers off of my motor to see if the bleed restrictors are gone.Well they are either gone or were never put in or they didnt use them on this model.According to my book they did,but my book shows a variety of motors starting late 60's to early 80's so my question...