Hi folks,
Have to replace port engine spark plugs wires, on my 87, 7.4 Crusader 350hp. Is anyone has a Name Brand or part # that will be cut for it. I hate universal set.
Henry G.
Have a 2000 7.4 GSI MFI. Cranks AND RUN GOOD UNTIL YOUR TURN ENGINE OFF. Crank but wont start within 6 to 12 hours after shutting off engine. Sparks OK, Fuel pumps running. Bad ECM ?????? Any help appreciated.
Like to know where is the knock sensor located on this 7.4 GSI, 2000, Engine will only start after a 12 to 24hrs stop. Was told by a (tech ?) when by-passed it will start all the time. Also said It was not available anymore.. Is the module with fins part of this knock sensor?Your help will be...
Just bought NGK BPR6FS to repl
Just bought NGK BPR6FS to replace my AC mr44t on both engines. Should I use same gaps? ( 0.035 in.) Mostly cruising @ : low RPM 1200 to 1500
Henry G.
Is anyone knows if these cross
Is anyone knows if these cross-over pipes are still available. Will hate to have to modify the complete exhaust system in my boat.
"Hi guys,
Need to flush the U
"Hi guys,
Need to flush the U-Cooler on my 454, 7.4 87 crusader port side engine, any suggestions how to do it? (muriatic acid?) Also is there an easy........way to remove the risers? do have crossover pipe on the exhaust sytem.
Your advice always...
Hi folks. I am ready to order
Hi folks. I am ready to order a replacement edelbrock 1409 for my Crusader 454 1987 engine. I was told I need an adaptor to replace my Rochester Q-Jet carb. Do I need a different fuel line from the pump to carb. or is is the same fuel line (direct match). Will send...
"Have a pair of Quadrajet, Roc
"Have a pair of Quadrajet, Rochester Carb. thinking about replacing with Edelbrock carb. Is anyone knows what CFM I need? was suggested 750 cfm, your expertise will be appreciated. Thanks
Henry G"
"Hi folks, I know I'm on t
"Hi folks, I know I'm on the wrong (BRAND) site, but it is for a friend, I need to find a site where I can get a wiring diagram (FREE IF POSSIBLE) for a 1986, 350, 5.7 V8, It's a Mercruiser engine. Henry G."
"is anyone know a site to get
"is anyone know a site to get the wiring diagram for Mercruiser 350, 1986. Need to know color code for wiring plug with pin #
Thanks in advance"
"have one bolt out, the other
"have one bolt out, the other one frozen salt solid, Bolt head gone, any suggestion how to remove bolt? Try PB Blast for a week, no result. Heat with propane torch, still not move. How about drilling? Any better ideas? Thanks
Henry G"
"Hi, Do have hundreds of new Q
"Hi, Do have hundreds of new Quicksilver parts in original unopened packages. Cannot find where these parts fits OB or I/O models. Any site(s) in mind. Also have many NLA parts (new)in stock. I can go to Mercury/Mercruiser parts site and find prices but no...
"Hi, Do have hundreds of new Q
"Hi, Do have hundreds of new Quicksilver parts in original unopened packages. Cannot find where these parts fits OB models. Any site(s) in mind. Also have many NLA parts (new)in stock. I can go to Mercury/Mercruiser parts site and find prices but no references to...
Is anyone knows where I can ge
Is anyone knows where I can get a pair of Carb. Base Gaskets for my Crusader model 350 (7.4L)I need 2 because of the 7 deg. riser plate. (straight shaft) Just rebuilt with an Echlin Carb. rebuilt Kit. Kind of easy to do.
"Is anyone knows where can I f
"Is anyone knows where can I find a complete Carburator rebuilt kit for my Crusader, 7.4L model 350,( 4 BBL)
Carburator looks like Carter/Weber Carb."