Logo
FULL SITE MENU

Recent content by bw94

  1. B

    '1989 70hp Evinrude

    I have a 70hp Evinrude, I'm having a hard time getting it started, and it's also idling rough, eventually dies. Compression is 130 on all 3 cylinders. Carb have been cleaned ( 3 times) and rebuilt. I replaced the VRO, with a standard fuel pump. Please, I need some help. Thanks
  2. B

    Somethings draining my battery

    "I think somethings draining m "I think somethings draining my battery, or at least that what it seems like, went to start it today. It turned over a few times,then the battery was dead,I charged it after I used it Thurs. It's a fairly new battery. Is there anyhting on the motor that might be...
  3. B

    Problem keep it running

    "It's a 70 hp Evinrude,&#4 "It's a 70 hp Evinrude,(TE70tlce). It takes a while to start, them when its running it will run rough then eventually die, almost like its starving for gas,it spits and sputters. Carbs have been cleaned 3 time already, the last time pretty good. Compression at 120 psi...
  4. B

    Prop spun out

    "Followed the advice that i&#3 "Followed the advice that i've read the forum,by marking the inside the hub with a marker, sure enough the prop spun. Is there a way to order the parts and fix it myself, or will i have to take it somewere to have it worked on.Model # TE70TLCE. Thanks"
  5. B

    Hard to start

    "I have problems stating my mo "I have problems stating my motor (te70tlce). I recently rebuilt the carbs, and cleaned them real well, soaked in Chem-Dip for 4 days,then in gasoline for a day, use small wires to get in all the small holes,a blew them out with air. It seemed to help my idle out...
  6. B

    Tell tale stream

    "Would it hurt anything to cha "Would it hurt anything to change the size of the tell tale outlet, from like 1/8 to 3/16?"
  7. B

    Tachometer

    "Where is the tach located, mo "Where is the tach located, model #te70tlce"
  8. B

    Low speed jetsdirty carbs

    "my motor #TE70TLCE, has the e "my motor #TE70TLCE, has the early production model carbs, where is the low speed jets located, whats the best way to clean the. The motor runs great at higher rpms but cuts out when it is idling. Thanks"
  9. B

    Crack in manual primer solenoid

    "Would having a crack in the p "Would having a crack in the primer solenoid keep the motor from running. The crack is on the front cover were the manual red level is. It looks like its were one of the screws is, i checked to see if there all tight,and they are."
  10. B

    Seafoam

    How do you use seafoam on an o How do you use seafoam on an outboard motor?
  11. B

    If I have a 12allon tank

    "If I have a 12 gallon tank, h "If I have a 12 gallon tank, how much oil would i have to mix with the gas at 50 to 1?"
  12. B

    Jwbmarine or joe reeves

    "i'm changing to a standar "i'm changing to a standard fuel pump from a vro, my question is where do the three hoses go. It's a pump from an '83 model 70 hp, going on an '89 70hp(TE70TLCE). I know the one that goes to the filter part of the pump,is the coming from the tank,and not to sure about...
  13. B

    Does anyone know

    "I'm trying to relocate th "I'm trying to relocate the telltale hose to the top of the block. My question is, after i drill a 11/32 hole, then tap with a 1/8 NPT. What's the part # of the nipple that i need to use,and will it work with a water pressure gauge? Thanks Alot."
  14. B

    Relocating Telltale

    Just wondering on which size d Just wondering on which size drill bit & tap to use. Thanks
  15. B

    Size of fuel line

    "I have a 70hp model# TE70TLCE "I have a 70hp model# TE70TLCE,should i use a 5/16 gasline or a 3/8, not sue what is on there, can't make it out"
See more
Back
Top