Logo
FULL SITE MENU

Recent content by aristakat

  1. aristakat

    2016 honda 250hp low fuel pressure when first start

    Need help.. after my 250 honda sits for a day it struggles for fuel at first.. if i squeeze primer bulb seems to help..once running and fuel in motor no issues ? So only at first start .. any thoughts on what us failing ?
  2. aristakat

    Bbjj honda 250 2016 anode zincs

    Our there other anodes /zincs besides two on lower unit, and one under trim pump ? I know some motors have zincs anodes on block ?
  3. aristakat

    Happy Thanksgiving to all

    Just wanted to take a second say in past how thankful I was to have everyone on here Jamie
  4. aristakat

    parts diagram for 2016 honda 250 ?

    looks on net for diagram for parts 2016 Honda 250's any one know have a link ? also service manual ? do you think old 225 maual will work ?
  5. aristakat

    Honda 225 , ,, need help #3 fuse 10 amp blowing

    Okay guys need help number 310 amp fuse keeps blowing. .I have disconnected rpm/hour gauge,, tilt ,trim switch on shifter... still blows... I can run motor at high rpm or running in plane w no problem..once I run at idle speed it blows,, also will blow w switch turned on while motor is...
  6. aristakat

    Honda 225 , ,, need help #3 fuse 10 amp blowing

    Okay guys need help number 310 amp fuse keeps blowing. .I have disconnected rpm/hour gauge,, tilt ,trim switch on shifter... still blows... I can run motor at high rpm or running in plane w no problem..once I run at idle speed it blows,, also will blow w switch turned on while motor is...
  7. aristakat

    need info on a serial number for honda 225

    Can someone find info on a 2007 Honda 225 such as is service bulletins have been done ie #56 etc..for me ? serial # bagj-1403788 thanks Jamie email is [email protected]
  8. aristakat

    Honda cowling not locking ?

    Ok need help , my top cowling on right side won't click or latch. I took middle cowling off to see it...I can see it's not cable, seems the tension arm that spring over to catch Latch might need a new spring ? Anyone ever had this issue ?
  9. aristakat

    need some help on 2002 honda 225

    ok ran motors out last week noticed one motor jumping/losing power... I feel like its starving for fuel/// I just changed all fuel filters ...runs fine low or normal rpms.. Only when I thortle fully does it act up on one motor ? any diagnostic help appreciated thanks Jamie
  10. aristakat

    honda 225 2002 need help motor seems to be starving for fuel or surging

    Replaced filter all replaced HP pump Cleaned vst tank Surges under load Pulled lap pump didn't see anything wrong Seems like fuel bulb gets soft when pumped motor runs better Any suggestions where to look ?
  11. aristakat

    here we go again bf225 honda 2002

    Hearing a intermittent clunking/thunging sounds.. Trying listening to w a tesascopecw local Mechanic.. he States could be a broken/loose pin connecting piston to connecting rod.. Or could be a bad bushing on connecttingrod.. Called two mechanics they both weeks out before can look at.. Any...
  12. aristakat

    hona 225 2002 cold start issue

    ok all would like some imput when I put boat in water starboard motor starts but fuel line doesn't prime up .. so I start motor while running I squeeze primer bulb till gets hard then all is fine ..my port motor has no issue like that .. what could be problem ? this motor had fuel pump...
  13. aristakat

    impeller change surprise

    ok so I took thermostats out poured a little salt away in each side used hose nozzle to flush out chambers dumping water into bucket to catch any pieces. There was no visible pieces so going to water test and keep an eye on it for the next few trips out not sure what happened to piece of...
  14. aristakat

    impeller change surprise

    Changing impellars today look what I found
  15. aristakat

    honda 225 2002 need help stripped screw ?

    ok need your help again guys went to change the high pressure fuel filter when pulling out the 3 screws the top screw started stripping hard to reach any suggestion how to get the screw out. Can't get impact driver to reach, how hard is it to pull entire fuel strainer off ?
See more
Back
Top