Boat Repair Forum

Port counter rotation engine starts and runs perfect to about 2800 rpm. Although I give it more throttle it doesn't respond.Used to run at 4000. No...

My father has a 28 ft Uniflite with twin chrysler 225 hp engines. One of them has developed a small hole in the oil pan. He was given a quote of 40...

its getting to be that time again and im looking to figure out what is going to be my plan this year for winterzation. Last year i paid the marina...

Guys im going to rent out the boat this year for the winter, this will be the first time i leave it in the water. I'm a bit worried about the...

I need help again.. 318 engine, Port sid of Port Engine. After 4 hours and second oil change lifters started making noise. Heads, Valves and Stems...

Raw water cooled 318LM has a cooling bypass in the thermostat housing. The 1970 TSB re-routed the bypass to the manifolds. So, how can the engine...

How hard is it to remove the part of the transmission that the coupling bolts into? I don't have enough room to drill out the bolts.

So I bought this beat up Lyman boat last year( see "more issues" thread and others) and both tanks read empty. It has the electric senders that read...

New longblock, intake and exhaust manifolds, new water pump (raw water cooled). Also new thermostat and housing. Problem is that it's running at...

Good morning, all - I've got a 1973 Luhrs 25 Sportfisherman with an LM318. I see from earlier posts that the timing looks to be 5 degrees BTDC, which...

The 360 Chryslers in my 34C Silverton have oil filters located right up against the stringers where they are really hard to remove without making a...

Trying to get my 1969 River Queen running... Anyone know where I can get parts at good prices? Right now, I specifically need boots. (Twin 318...

Hello! I'm new to the site and this is my first post. I'm also new to a 1968 34' Nautaline with a single Chrysler 318 engine. I really don't know...

I was putting new points in today in my 72 luhrs, with a 318, I took off the contact plate to see if there was any corrosion on the advance...

The starboard engine in my 1975 Marinette has decided not to idle properly. It was tuned up and ran great for about 6 hours (3 trips) then started to...

I have stalling isses on my starbord side 360. it seems to happen only when warmed up and after running a bit. I've stalled out at the dock, after...

Background - twin 318s with closed loop cooling. Port engine runs 175F and starboard can get up to 200F. Back flushed the raw water path and found...

Need to remove a failed oil pressure sending unit on my starboard Chrysler 360. I confirmed it was bad by wiring the starboard gauge to the port...

Hello My 318's voltage readings' @ batteries are 14.50 when running. Is this two high of a charging rate? I have the internal voltage regulators...

So here is the situation: I have twin 318's in my boat paired up with Paragon v-Drives. I had the boat out of the water last week for tranny work and...

dave med Junior Member Join Date: Jul 2010 Location: Massachusetts ...

Has anybody resolved a fluctuating tach issue? It happens at around 1000 rpm in idle no load. If I throttle up, it smoothes out. The tach is not the...

I have a 1985 318. The oil pressure is usually about 60lbs. The pressure has slowly (about an hour) dropped to below 5lbs. The oil looks good and...

I was wondering if anyone could provide me the spec's on a 1981 Chrysler 360. I especially need timing, sparkplug plug info, dwell, etc any and all...

I need a rebuild on my carter afb's and would like to get them done quickly so i was just wondering if anyone knows if a rebuild for an automotive...

greetings . . . I'm looking for exhaust manifolds (good used ones, by chance). Would anyone have a pair for sale? (1986 LM318)

Hey Guys, I'm new to this forum. I have a 1976 18' galaxie jet crusier, with a AMC (which I believe is the same engine as Chrysler) 360 with a...

Found Water in my Paragon V-drive. Should be simple fix (gasket). Question is, can I disconnect the cooling water short term until part located? ...

Is this time for a rebuild or does the tranny sound like this! http://www.youtube.com/user/captlazybone#p/u/0/rWi3HuAz7sw Done some research...

Have new Edelbrock carbs on the way. Jeff (yes the famous Jeff) says there's no vacuum source to use a vacuum gauge for tuning. Do you guys...

OK, so I've asked around at my favorite sea dog haunts and I don't get much in the way of opinion or advice! So I pulled out all the old oil and...

Hello, I just installed 2 new Mallory distributors on my 1978 318 Chyslers with electronic ignition. After installing one on my starbord engine...

I was at my marine mechanics shop last weekend, dealing with my old inboard. He was pulling the engine from an ’09 Glastron, because it needed a new...

Just bought a 1974 Trojan 25 foot with a Chrylser 1976 360 engine. Only took it out 3 times and the engine blew. Had it re-manned, found out they...

My 318 LM is missing the timing index. How do I set the timing? I have been looking for the part, but no luck yet. There is a mark on the flywheel...

Hi everyone, I have a Chrysler 300ha stern leg that I am currently rebuilding.....Or at least trying too. It is Proving very hard to get parts for...

"I was at the marina last Saturday afternoon and the owner was telling me about 2 girls who were sitting on a jetski that morning trying to get it...

"I have gasoline in the raw water exhaust of my chrysler 360. The engine idles and runs at higher rpms fine and is not running roughly. The engine...